# embedding_metadata

key: chroma:document
string_value:
Starting & Driving Adaptive Cruise Control When activated if the adaptive cruise control Adaptive Cruise Control System System * system detects a vehicle in the same lane Activation directly ahead it may accelerate or gently apply braking of the vehicle to maintain the After following the vehicle ahead The adaptive cruise control system set following distance. to a stop, the driver must observe is designed as a comfort system enabling the driver to maintain Note: The adaptive cruise control system any local traffic laws and ensure a constant speed or distance is designed for highways and roads in that there are no obstacles or from the car in front. It provides good condition. It is recommended not other traffic participants, such assistance to the driver, it DOES to be used on urban roads and mountain as pedestrians, directly in front NOT replace any of the drivers roads. of the vehicle before allowing it responsibilities. When using the to pull away and begin to follow adaptive cruise control system, the vehicle ahead again. it is important that the driver Whilst using the car following maintains concentration at ALL cruise function it is strongly times and is prepared to take recommended that the driver action. Otherwise, accidents or does not touch the accelerator personal injuries may occur. pedal. Any activation of the The adaptive cruise control system can accelerator will not allow automatically switch between constant speed the system to automatically cruise and car following cruise depending on apply the brakes should this be whether it can detect a vehicle directly ahead. necessary. Constant speed cruise controls the vehicle at a certain speed range. Car following cruise DO NOT exit the vehicle when the operates by setting the distance between the adaptive cruise control system vehicle and the vehicles directly ahead. car following cruise function has stopped the car, or is keeping the car stationary. Before exiting the 156


key: chroma:document
string_value:
Starting & Driving car the shift control knob should 1 With the vehicle START/STOP Switch be in the Park position and the in the ON/RUNNING position, if the START/STOP Switch in the OFF adaptive cruise lever switch is in the position. ‘OFF’ position (7), then the adaptive cruise control system is switched OFF. If the adaptive cruise control 2 Move the adaptive cruise lever switch to system has already stopped the the ‘ON’ position (4), the adaptive cruise vehicle, and the adaptive cruise system status indicator on the instrument 4 control function is disabled, pack illuminates yellow, the adaptive turned off or cancelled, the cruise control system is in the Standby vehicle will no longer stay still, mode. it may move forward or slip 3 The system will automatically detect the backward. When the vehicle is speed and position of the vehicle ahead, 1 Speed Limit Increase/Accelerate stopped and kept still by the if your vehicle speed is above 5 km/h, adaptive cruise control system, 2 Speed Limit Decrease/Decelerate after pressing the ‘Set’ button (6) at the be sure to be ready to apply the 3 Cancel end of the adaptive cruise stalk lever, brakes manually. 4 Standby the indicator on the instrument pack will turn green, and the adaptive cruise 5 Resume When driving on a bend, the control system enters the Activated adaptive cruise control may 6 Set mode, its target speed is the actual speed actively reduce the vehicle speed 7 OFF at activation; if your vehicle speed is less to maintain vehicle stability and than 30 km/h, then the target speed of 8 Increase Distance safety. the system is set at 30 km/h. If the speed 9 Decrease Distance of the vehicle ahead is greater than the cruise target speed of your vehicle, your The adaptive cruise control system is vehicle will maintain the target speed operated with a lever switch, which is located to conduct constant speed cruise. If the under the left side of the steering wheel. speed of the vehicle ahead is lower than 157


key: chroma:document
string_value:
Starting & Driving the cruise target speed of your vehicle, Adaptive Cruise Target Speed 4 When using the lever to adjust the target it will enter the car-following cruise. An Adjustment speed, briefly operate the adaptive cruise image of your car and the car ahead is lever switch upward (1) or downward When the adaptive cruise control system is displayed in the instrument pack message (2) once, the target speed will change 5 activated: centre. In this mode the actual speed may km/h, press and hold the lever upward or be less than the set target speed. Whilst 1 Use the accelerator pedal to reach the downward and the speed will increase or in the car following cruise mode, you can desired speed, short press the ‘Set’ decrease in 1 km/h increments, release follow the vehicle ahead to a stop. If the button (6) on the end of the adaptive the lever when the desired speed reading parking time is less than a preset time cruise switch lever, release the control is displayed. period, your vehicle may automatically button and accelerator pedal. The vehicle pull away to follow the vehicle ahead, will cruise at the desired speed. Note: If the vehicle ahead continually or you need re-activate the adaptive makes hard acceleration or deceleration 2 Move the lever switch upward (1) and cruise control system using the method manoeuvres the adaptive cruise control hold, the target speed will increase until displayed. may not be able accurately maintain the desired set speed appears in the the required distance between vehicles. Note: Manual deactivation of either instrument pack, then release the switch. It is important that the driver always the Traction Control System (TCS) or When it is confirmed that there is no concentrates and pay attention to the Stability Control System (SCS) will vehicle in front of your vehicle or the inhibit the operation of the adaptive vehicle ahead exceeds the preselected current vehicle position and situation cruise control system. following distance, the speed will be in case they need to make a braking or increased to the set speed. avoidance manoeuvre. 3 Move the lever switch downward (2) and hold, the target speed will decrease until the desired set speed appears in the instrument pack, then release the switch, the vehicle speed will decrease to the set speed. 158


key: chroma:document
string_value:
Starting & Driving Adaptive Cruise Target Adaptive Cruise Pause/Standby • Follow the vehicle ahead to a stop and Following Distance Adjustment the stop time exceeds a certain period When the adaptive cruise control system of time. When the adaptive cruise control system is is activated, move the lever switch to the activated, rotate the switch on the end of ‘Cancel’ position (3), and the system will exit • The camera or radar view is blocked, the lever upward (8) or downward (9) to to the Standby mode. the surrounding environment triggers adjust the following distance, you are able the preset safe exit mechanism of the to toggle between 3 distance settings which Automatic Deactivation of sensors, or the system fails. 4 are displayed in the message centre in the Adaptive Cruise Note: If following the vehicle ahead to instrument pack. In the following situations, the adaptive a stop with the adaptive cruise control Always select an appropriate following cruise control system may be automatically system enabled, if any of the following distance that is relative to the current speed deactivated, this transfers full control of the conditions occur whilst the vehicle of your vehicle and the vehicle you are vehicle to the driver. is in a stopped state, the EPB will following, the greater the speed, the • Move the lever switch to ‘OFF’ position automatically be applied: further the distance. ALWAYS consider (7). • The driver unfastens his/her seat belt. current traffic, road and weather conditions • Press the brake pedal whilst the vehicle when making your selection. • The driver door is opened. is in motion. • The stationary time exceeds the • Move the rotary gear knob to either R or preset time period. N position. • The driver unfastens his/her seat belt. • Press and hold the accelerator pedal beyond a preset time period. • Open any door, bonnet or tailgate. • Pull the EPB switch up to apply the parking brake. 159


key: chroma:document
string_value:
Starting & Driving Adaptive Cruise Override Adaptive Cruise Control System • Enters and leaves a tunnel or drives in the Impairment and Ineffectiveness tunnel. If the driver has cause to use the accelerator pedal when the adaptive cruise control system • Encounters a vehicle or object which is • Drives in the shade of mottled trees. is activated, the vehicle will remain in Cruise stationary or traversing the lanes. • Excessive weight being carried in the mode while the vehicle speed increases. • Approaching the vehicle ahead too fast, boot space or cargo area causing the When the accelerator pedal is released, the and the system cannot apply sufficient front of the car to point upwards. adaptive cruise control system will resume to braking force. operate at previously set cruise speed. • The vehicle ahead is an oncoming Adaptive Cruise Resume vehicle, or makes an emergency braking manoeuvre. If the adaptive cruise control system has reverted to, or been switched to, the Standby • A vehicle suddenly cuts into the lane in mode it can be reactivated by moving the front. lever switch to the ‘Resume’ position (5). • Encounters a vehicle driving at a low The target cruise speed will automatically speed. be set to the target speed before exiting the • Encounters a vehicle with loaded items adaptive cruise control system. protruding from the body profile of the vehicle. Clear Speed Memory • Encounters a vehicle with a higher chassis If the lever switch is moved to the ‘OFF’ (e.g., a truck). position (7) or the vehicle START/STOP Switch is switched to the OFF position, the • Encounters pedestrians, non-motor system may clear the adaptive cruise control vehicles or animals. set speed in the memory. • The vehicle is driving on an uneven road or a complex traffic road section. • The vehicle makes a sharp turn. 160


key: chroma:document
string_value:
Starting & Driving Special Driving Environments The adaptive cruise control system has it’s limitations. Listed below are some conditions that may be beyond the safe operating limits. The driver should maintain control of the vehicle and must remain alert at all times. They should pay special attention to the 4 traffic conditions and surroundings, select the appropriate speed and be ready to take any required actions. When turning at an intersection or following If the vehicle ahead changes lanes, but does a vehicle into, or out of a curve, the adaptive not drive into the lane completely, the cruise control system may be unable to detect adaptive cruise control system may be unable the vehicle ahead, even if it is in the same lane, to detect the vehicle. it is possible the system may detect a vehicle If the vehicle ahead changes lanes, but does in another lane. not exit the lane completely, the adaptive cruise control system may determine that Note: Do not use the adaptive cruise the vehicle ahead has exited the lane and control system on entrance/exit ramps accelerate to any preset speed. or sharp bends. 161


key: chroma:document
string_value:
Starting & Driving When driving on uneven roads that may • Driving through roadworks or Driving Assist System * include steep climbs or dips please DO NOT construction sites. The driving assist system can detect the road use the adaptive cruise control system. • Driving on low friction roads. and environmental information ahead of the vehicle by utilising a front view camera and a front detection radar under certain conditions. This information is used to relay warning messages or provide assistance to help the driver in controlling the vehicle in a safer and more reliable manner. The front view camera is located in the interior rearview mirror base cover, the front detection radar is located at the lower middle of the front bumper. When driving behind a vehicle that is only Note: DO NOT operate any partially overlapping your vehicle, ‘A’ in the infotainment switches whilst driving. If graphic, the adaptive cruise control system you wish to make any settings changes, may be unable to detect anything. please pull over when it is safe and legal Note: Please DO NOT use the adaptive to do so. cruise control system in the following situations: • Driving in bad weather conditions. • When the ambient light is insufficient, the light is too much, or the front lighting of the vehicle is poor. • Driving on rough or poor road surfaces. 162


key: chroma:document
string_value:
Starting & Driving Description of Front View Obstruction of the front view excessive water (rain), frost or water Camera camera spray from the road on the windscreen. On occasion the front view camera view may • The windscreen viewing area is damaged. Calibration of front view camera become obstructed by foreign objects or • Not calibrated after removing/refitting The front view camera will require re- stains on the glass. In these cases a prompt the front view camera or the windscreen. calibration after any of the following message will appear in the information centre. • The front view camera is not secured in operations: Please wipe or clean immediately. 4 place. • Removal and refitting of the front view In the following situations, the detection camera. performance of front view camera will • Replacement of the windscreen. be affected: Note: The calibration of front view • Driving in poor weather conditions camera requires professional knowledge where visibility is reduced due to thick and tools. If calibration is required, fog, heavy rain, snow, dust or sand storm please seek an MG Authorised Dealer. etc. • Affected by light, for example low light levels at night, poor auxiliary lighting, excessive backlighting in the view, light from oncoming vehicles, abrupt change of brightness with a quick bright/dark jump (tunnel entrance/exit), driving on surfaces with strong reflective properties (road surface covered with water or snow), tunnels, inside a building etc. • The front view camera view is partially or fully blocked by obstacles, e.g. dust, foreign objects, oil pollution, mud, snow, 163


key: chroma:document
string_value:
Starting & Driving Description of Front Front radar performance will be effected in Note: Any snow that gathers on the Detection Radar the following situations: front radar may be removed using a soft brush, and any ice should be removed • When the front detection radar is Calibration of front detection covered by mud, snow, excessive water using a propriety deicing spray. radar (rain) or water spray from the road. Note: Avoid any collision or contact The front detection radar re-calibration is • When the radar or surrounding areas with the front radar module, this may required after any of the following: are covered by objects such as labels or cause misalignment. auxiliary lighting installation. • The front detection radar mis-alignment failure, for example the position of the • When the front detection radar is subject front detection radar has changed. to strong vibration or slight impact. • Remove/refit the front detection radar or • Some targets may affect and weaken the radar bracket. detection capability of the front detection radar, such as road barriers, fences and • Remove/refit the front anti-collision tunnel entrances. beam. • When the front detection radar is • The four-wheel alignment parameters affected by the environment, such as have changed. strong electromagnetic field interference or due to the target itself. Note: If the front detection radar is subject to strong vibration or slight • Strong reflected radar signals (such as: in impact, the mounting position of the multi-storey car parks, tunnels, sprinkler front detection radar needs to be spray systems or water jets etc). Experiencing any of these could cause the checked and re-calibrated as necessary. function of the front detection radar to Note: The calibration of front detection be effected. radar requires professional knowledge and tools. If calibration is required, please seek an MG Authorised Dealer. 164


key: chroma:document
string_value:
Starting & Driving Speed Assist System the instrument pack. The system will automatically intervene and maintain speed control to keep the vehicle speed The intelligent speed limit is an 1 Speed warning Function (Speed warning): within the permitted maximum speed auxiliary function, it may display The vehicle detects a speed limit sign limit. And an acoustic warning and a an incorrect speed limit value (as shown above) at the roadside with visual warning will be available during the or no speed limit value in the the front view camera. The speed limit intervention. instrument pack due to various sign identified will be displayed on the 4 factors. As a result, the vehicle instrument pack. When the vehicle Speed assist system setting speed is not restricted within the speed exceeds the speed limit by a The operating interface for the speed correct range. The driver still preset amount, a visual warning in the assistance system is located in the infotainment needs to observe the speed limit instrument pack will alert the driver to display. Enter the vehicle setting interface to of the road traffic, and speeding control the speed manually. locate the driving assist option, scroll across is strictly prohibited. the page to find the setting interface for the 2 Manual Speed Assist (Manual): The speed assist system: driver sets the target speed limit value The front view camera cannot using the adaptive cruise control lever. • 1 Touch the corresponding button on the recognise speed limit signs The system will actively intervene and infotainment display to select the speed painted on the road surface. keep the vehicle speed within the target assist mode: off, Speed warning, Manual The driver MUST observe these speed limit. An acoustic warning and a and Intelligent. speed limits and adjust the their visual warning will be available during the speed accordingly. intervention. Please refer to the section “Speed settings of manual speed assist”. The speed assist system settings are available 3 Intelligent Speed Assist (Intelligent): via the infotainment system. When the The vehicle detects a speed limit sign adaptive cruise control system is OFF, the (as shown above) at the roadside with following three functions can be selected: the front view camera. The speed limit sign identified will be displayed on 165


key: chroma:document
string_value:
Starting & Driving Speed settings of manual speed 2 After the manual speed assist function assist: is activated, the system will actively When the speed warning function intervene and keep the vehicle speed or intelligent speed assist function is enabled, After the manual speed assist function is within the target speed limit. If the the system indicator lamp on the instrument enabled, the speed limit value can be set by current actual speed exceeds the target pack illuminates green. using the adaptive cruise control lever as speed limit value set by the driver, the follows: system will reduce the speed until it is When the manual speed assist function is below the target speed limit. enabled, the system indicator lamp on the 1 With the manual speed assist function instrument pack illuminates yellow. When enabled, the initial speed limit value is 3 After the manual speed assist function is the function is activated by pressing the SET displayed as “—” on the instrument pack. activated, the driver can press the SET button on the adaptive cruise control lever, Press the SET button (3 in the figure button (3 in the figure below) on the the system indicator lamp illuminates green. below), the manual speed assist function adaptive cruise control lever to reinstate will be activated. The first time pressing the system to standby state. Press the If the speed assist system detects a fault or the set button, if the current actual speed SET button again, the manual speed assist failure, the indicator lamp will flash yellow is lower than 30km/h, the speed limit function will be resumed. then extinguish. value displayed in the instrument pack is defined as 30km/h; if the current actual speed is higher than 30km/h, the speed When the speed warning function limit value displayed in the instrument or intelligent speed assist function is enabled, pack will be defined by the current actual the speed limit value indication illuminates. speed. Moving the lever up or down The “NNN” is displayed as “—”. When once will increase or decrease the speed the vehicle passes the first speed limit sign limit value to the rounding up value or identified, the speed limit indication displays rounding down value, then moving up or the real-time speed limit value. down once will increase or decrease by Note: When the vehicle needs to change 5km/h. Holding the lever up or down, the lane, make a turn or turn around at speed limit value will continuously change in units of 5km/h. an intersection and the driver uses an indicator in advance and slows down, 166


key: chroma:document
string_value:
Starting & Driving the original speed limit value on the change to yellow. Press the SET button 6 Non standard speed limit signs or signs instrument pack will be reset and again to resume the functions. that contain additional information. displayed as “—” until a new speed limit 3 Move the adaptive cruise control 7 The speed limit signs set up at a fork in sign is detected. If the conditions are not lever to “ON” position to switch the the road, on a bend or on-ramp/off-ramp. met, the original speed limit value will speed assistance system off. Then the 8 During manoeuvres such as lane- be maintained and not be reset. The indicator lamp in the instrument pack will changing. driver MUST observe the speed limits extinguish. 4 and adjust the their speed accordingly. The speed limit information function When the manual speed assist function is and intelligent speed limit function may enabled, the speed limit value indication be impaired in the following situations: illuminates. The “NNN” is displayed as “—”. Press the SET button to activate the manual 1 The detection performance of front view speed assist function, The “NNN” is displayed camera is affected. as 30km/h or the current actual speed. Move 2 The vehicle is driven at a high speed. the adaptive cruise control lever up and down 3 The speed limit signs are obscured by to adjust the target speed limit value. trees along the road, ice/frost, snow, The driver can directly switch off, or dust, etc. temporarily suspend the speed assist system 4 The speed limit signs are incorrectly by carry out the following actions: placed or damaged. 1 To temporarily exceed the speed limit 5 There are multiple speed limit signs (overtaking manoeuvre), press the above the lane or on the sides of the accelerator pedal hard. The indicator road. Currently, the front view camera lamp in the instrument pack illuminates can only recognise the speed limit signs green, and the speed limit value flashes. for the lane in which the vehicle is being 2 Gently press the SET button on the end driven. of the adaptive cruise control lever, the indicator lamp in the instrument pack will 167


key: chroma:document
string_value:
Starting & Driving Lane Assist System The lane assist system switch is located in the IMPORTANT infotainment display. Enter the corresponding • The camera may not correctly The lane assist system is an interface for driving assistance to turn the recognise speed limit signs during poor auxiliary system that provides system ON/OFF, and make mode selection. lighting conditions, bad weather, non- assistance to the driver. It does standardized or sheltered speed limit Lane Departure Warning NOT remove the responsibility signs or the camera’s own restrictions of safe driving from the driver. The system uses the front view camera to which include the recognition of similar signs (e.g., recognise a weight When choosing to use the lane detect the lane lines ahead of the vehicle. The limit sign as a speed limit sign, or assist system, the driver MUST system will be activated when the following recognise a minimum speed sign as the always pay attention to the detection conditions are met: maximum speed sign). surroundings, hold the steering • The function is switched ON, wheel and be prepared to make • Some drastic or rapid steering operations made by the driver may manoeuvres at any time. Failure • Vehicle speed is above 60 km/h, be judged as changing lane or turning to maintain overall control of • Lane line markings are clear and the around at an intersection by the the vehicle may result in an system recognises at least one lane line. system. This will result in the identified accident or personal injury. When a wheel is about to cross the lane line, speed limit signs being cleared. or has already crossed the line, the system The lane assist system does will provide warnings to prompt the driver to not always recognise the lane take action and maintain the vehicle position lines. Sometimes poor road between the lane lines. The function will surfaces, certain road structures automatically exit when the vehicle speed or objects may be mistaken for drops below 55 km/h. lane lines. When such situations occur, the lane assist system must be immediately turned off. 168


key: chroma:document
string_value:
Starting & Driving Lane Departure Prevention Lane Keeping Assist IMPORTANT The system uses the front view camera to The system uses the front view camera to • In cases where the number of lanes detect the lane lines ahead of the vehicle. The detect the lane lines ahead of the vehicle. The increase or lanes merge, the driver system will be activated when the following system will be activated when the following MUST take full control of the vehicle. detection conditions are met: detection conditions are met: • In areas where there are complex • The function is switched ON, • The function is switched ON, traffic conditions such as intersections • Vehicle speed is above 60 km/h, • Vehicle speed is above 60 km/h, or road junctions with congestion, the 4 driver MUST take full control of the • Lane line markings are clear and the • Lane line markings are clear and the vehicle. system recognises at least one lane line. system detects lane lines on both sides of the vehicle. The lane assist system will be impaired or When a wheel is about to cross the lane line, The system will always attempt to maintain ineffective in the following conditions: or has already crossed the line, the system the vehicle position in the centre of the lane will provide assistance to the driver by • The hazard lamps are activated. by using corrective steering interventions. keeping the vehicle in between the lane lines If the vehicle deviates from the lane lines • The driver indicates in the direction of by applying corrective steering intervention too much, the system will activate the alert the lane line about to be crossed. and simultaneously displaying a prompt. If the function. The function will automatically exit vehicle deviates from the lane lines too much, • The driver applies the accelerator rapidly, when the vehicle speed drops below 55 km/h. the system will activate the alert function. carries out an emergency manoeuvre or The function will automatically exit when the In the absence of a steering input from the makes a hard brake pedal application. vehicle speed drops below 55 km/h. driver for a certain period of time, the system • The system detects that the driver will provide warnings. has not moved the steering wheel for a preset time period (in the mode of departure assist or lane keeping). • During system intervention the steering wheel is operated (in the mode of departure assist or lane keeping). 169


key: chroma:document
string_value:
Starting & Driving • The lane line is too thin, damaged, or It is recommended to turn off the lane Forward Collision System fuzzy. assist system in the following situations: • The vehicle is driven on the bend with • Driving in a sports style or manner. The driver remains responsible a small curvature radius, the road is too for the safety of the entire • Driving in bad weather conditions. narrow or too wide. driving process, even if the • Driving on rough or poor road surfaces. vehicle is equipped with a • The vehicle has just entered a road forward collision system. The section with lane lines or is driven on a • Driving through roadworks or road section without lane lines. construction sites. driver MUST pay full attention and drive carefully. As with all • The vehicle changes lanes or sways the driver assist systems, the laterally too fast. forward collision system cannot • The vehicle is not in D. prevent accidents or avoid collisions in all situations. The • The vehicle speed is below 55 km/h, or driver MUST always remain in too high. control to avoid accidents or • The anti-lock brake system (ABS) and the emergency situations. dynamic stability control system (SCS) are activated. Emergency braking whilst under • Faults exist in the anti-lock brake system the control of the forward (ABS), dynamic stability control system collision system may cause (SCS), electric power steering system injuries to the passengers. (EPS), etc. Therefore, drive carefully and all passengers MUST wear seat belts at all times. 170


key: chroma:document
string_value:
Starting & Driving Alert accidents. If the vehicle is braked and stopped Ensure the forward collision under the system control, it will remain When the system detects that there is a system or vehicle power system stationary for a short time. Full control of the risk of collision between the vehicle and the is switched off when being vehicle will then be returned to the driver. vehicle in front in the same lane, warnings towed. If the forward collision will be provided to prompt the driver to The system will only slow down the vehicle system is enabled when the slow down in time and keep a relatively safe automatically if the following conditions are vehicle is being towed, adverse distance from the vehicle ahead. met: effects may affect the safety of 4 • The dynamic stability control system your vehicle, the towing vehicle Emergency Braking (SCS) and traction control system (TCS) and the people around. When the system detects that there is a are fault-free and ON. risk of collision between the vehicle and the • The vehicle is in D or N. To avoid the occurrence of vehicle directly in front of the vehicle, the accidents, never specially test • The airbags are not deployed. brake system will automatically intervene to the functions of the forward decelerate the vehicle, so as to avoid collision Note: In some cases, the driver may collision system. accidents or mitigate damage from collision not have anticipated any braking The forward collision system switch is accidents. If the vehicle is braked and stopped intervention and does not want to apply under the system control, it will remain located in the infotainment display. Enter the the brakes whilst the forward collision stationary for a short time. Full control of the corresponding interface for driving assistance system is braking heavily, the driver can vehicle will then be returned to the driver. to turn the system ON/OFF, and make mode temporarily cancel this operation by selection. heavily pressing the accelerator pedal Pedestrian auto emergency after ensuring that it is safe to do so. braking When the system detects that there is a risk of collision between the vehicle and the mobile pedestrian directly in front of the vehicle, the brake system will automatically intervene to decelerate the vehicle, so as to avoid collision accidents or mitigate damage from collision 171


key: chroma:document
string_value:
Starting & Driving The operation of the forward • The contour of the vehicle ahead is • Objects such as signs, guardrails, bridges, collision system may be impaired or unclear (such as water being sprayed by buildings or other are detected in front ineffective in the following situations: the wheels of the front and surrounding of the vehicle. vehicles). • The vehicle is being driven on hillside • The vehicle ahead approaches head-on, • The vehicle ahead does not have or has road, upper and lower bridge section or crosses the intersection or jumps the obscured tail lamps when driving at night tight bend. queue rapidly in a short distance. or in a tunnel. • The vehicle is in R. • The vehicle ahead does not follow the • The tail lamps of the vehicle ahead are rules of driving and parking (such as • The vehicle is in the state of braking or all LED strip lights or other homemade drives on the lane lines). rapid acceleration. coloured lamps. • The vehicle ahead is not in the same lane • The street lights are inconsistent or as your vehicle or the vehicle ahead is flickering when driving at night. partially obscured. • The pedestrian is not directly in front of • The vehicle ahead is an abnormal vehicle the vehicle, or the pedestrian is not fully (modified or abnormal shape). visible. • The vehicle ahead is a vehicle with higher • The pedestrian is not standing upright, or chassis. it is a child under a certain height. • The vehicle ahead is large vehicle at close • In front of the vehicle are a crowd of range (such as tractor, trailer, towing pedestrians, the pedestrian is over- vehicle, mud truck, sanitation truck, shadowed or in the dark. sprinkler truck etc.). • There are animals in front of the vehicle. • The vehicle ahead is unusual transportation (such as a horse, cart, • Objects such as special-shaped ground carriages etc.). obstacles (e.g. roadblocks, isolation piles, isolation strips, large stones, other • The system detects the side of a vehicle. scattered objects etc.) are detected in front of the vehicle. 172


key: chroma:document
string_value:
Starting & Driving Active Speed Limit (ASL) The ASL system shares the same lever switch upwards or downwards and hold, the target System * as the cruise control system, located to the speed limit value will change continuously in left of the steering wheel below the indicator units of 5km/h. The range of target speed stalk. The switch can be toggled between adjustment is 30 - 200km/h. both functions, however only one function can operate at any one time. When activated if the vehicle speed is greater than the user inputted target Activate speed the system will begin to slow the 4 vehicle to the inputted target. The desired target speed of the ASL system is displayed in the instrument information When ASL is active, pressed the cluster. accelerator pedal fully (eg: overtaking) With the START/STOP Switch in position can make the vehicle speed increased. ON/RUNNING and the lever switch in “ASL When released the pedal, vehicle speed • Speed Limit Increase (1) Standby” (3 in figure), the ASL function is in will subject to the target speed limit standby mode. Pressing the “Set” button (5 value. in figure) will activate the ASL system. When • Speed Limit Decrease (2) activated and vehicle speed is less than or Suspend ASL • ASL Standby (3) equal to 30 km/h, then the target speed limit value will be set at 30 km/h by default. When When ASL is active, to suspend the feature • Cruise Standby (4) activated and vehicle speed is higher than 30 press the “Set” button (5 in figure) and the km/h, then the current vehicle speed will be ASL system will exit to the standby state. • Set (5) set as the target speed limit value. Firstly, the target speed limit value will be rounded Resume ASL The Active Speed Limit (ASL) system is when the lever switch is moved upwards or If the system has been placed in a standby designed to control the vehicle speed keeping downwards. Then, the target speed limit value state with a retained target speed the system it below a speed set by the driver. will be increased or decreased by 5 km/h can be reactivated to the previously stored every time the lever switch is briefly moved target speed by pressing the “Set” button (5 upwards or downwards. Move the lever in figure). 173


key: chroma:document
string_value:
Starting & Driving Note: When ASL is suspended, if the Parking Aid System Rear Parking Aid accelerator pedal is fully depressed (eg: The ultrasonic sensors in the rear bumper overtaking), the system can not be reactivated. Ultrasonic Sensor Parking Aid monitor the area behind the vehicle to search for obstacles. If any obstacle is detected, the Exit ASL The purpose of the parking aid system will calculate its distance from the is to assist the driver in reversing! Pull the lever switch to “Cruise Standby” rear of the vehicle and communicates the position (4 in figure), ASL system will exit. The sensors may not be able message to the driver by sounding warning to detect obstacles of certain chimes. Note: ASL system brakes the vehicle relied type, e.g. narrow posts or small on the engine, which has limited braking objects no more than a few Parking Aid in Operation capacity. ASL is not a substitute for the inches wide, small objects close brakes. In case of steep slopes and other The rear parking aid is enabled automatically to the ground, objects above the needs to brake quickly, please press the brake when reverse is selected, it is switched off as tailgate and some objects with pedal to brake the vehicle. soon as reverse is disengaged. A short beep is non-reflective surfaces. given by the parking aid within 1 second after selecting reverse to indicate that the system Keep the sensors free from dirt, is operating normally. ice and snow. If deposits build up on the surface of the sensors, Note: If a longer, higher pitched sound their performance may be is emitted for 3 seconds when reverse impaired. When washing the car, is selected this indicates a fault in the avoid aiming high pressure water system. In this case seek assistance from jets directly at the sensors from your MG Authorised Dealer. close range. With the parking aid enabled, when obstacles are detected, the system will give sounds in different frequencies (there might be blind areas). 174


key: chroma:document
string_value:
Starting & Driving Parking Camera System * 360 Panoramic Imaging System * The purpose of the parking The purpose of the 360 camera system is to assist the panoramic imaging system is to driver in reversing! The camera assist the driver during reversing! has limited field of view and The cameras have a limited cannot detect obstacles outside field of view and cannot detect the field of view. 4 obstructions outside the field of view. • If there is an obstacle within 1.2m range from the rear sensors, the system starts Although the entertainment to emit a beeping sound. As the vehicle display can provide high- moves closer to the obstacle, the beeps definition images around the are transmitted more rapidly. vehicle, please still pay attention • Once the obstruction is within 30cm to the current actual road range of the rear bumper, the beeps will conditions for your driving safety merge into a continuous warning. Make sure the exterior rear-view mirror is deployed, when using The parking camera is fitted between left the 360 panoramic imaging and right license plate lamps. When the system. reverse is selected, the camera will display an image of what is directly behind the car in the entertainment display, and the system supports the indication of distance from obstacles to vehicles. 175


key: chroma:document
string_value:
Starting & Driving With the 360 panoramic imaging system Rear Driver Assistance working, the display interface will show System * The system has limitations and a 360° panoramic image of the vehicle to may not be able to warn of facilitate the observation of the surrounding vehicles approaching at high System Overview environment. you are able to touch different speeds. areas around the vehicle to check images The effective recognition from different angles of view. capabilities of the rear sensors The rear driver assistance The 360 panoramic imaging system can be function is only an aid, it is NOT can be limited by objects such accessed in the following ways: a substitute for the attention of as roadside buildings, guardrails, • Select R gear. changes in pitch angle of the the driver. The driver must always remain in control, observe the • Press the 360 view button. car due to heavy loading, road surroundings and drive safely. • In the setting interface, turn on the conditions such as bends or turning assistant display function. At low bumps or weather conditions The correct operation of the speed, turn on the left or right corner such as snow and ice etc. Any rear sensors will be compromised light. of the above may trigger a false if they are misaligned due to alarm. In the 360 panoramic image display interface, accident damage. This may cause press the settings button to personalize the the system to automatically relevant functions of the system. The rear driver assist system may shutdown. not provide adequate warning of Note: When the shift lever is placed very fast approaching vehicles or To ensure that the radar in forward gear position, in no case operate correctly on tight curves sensors work correctly, the rear can 360 panoramic imaging system be of 500m radius or less. bumper should be kept free of enabled as long as the vehicle speed snow and ice and must not be exceeds or equals to 15 km/h. The rear driver assist system covered. will not operate correctly whilst towing a trailer or caravan. 176


key: chroma:document
string_value:
Starting & Driving state. During the calibration process, the Use of non recommended system will provide limited functions, materials or paint on rear and the alarm may be inaccurate. bumper repairs may have Upon completion of the calibration, the a detrimental effect on the system will resume all functions. operation of the rear sensors. Please only use recommended Switching the System Functions materials. On/Off 4 The rear driver assistance system includes The rear driver assist system function and blind spot detection (BSD), lane change assist sub system switches can be accessed via the (LCA), and rear cross traffic alert (RCTA) infotainment screen. functions. Select ON/OFF to activate/deactivate the system. The rear driver assistance modules are mounted at the rear of the vehicle on each System Functions side, they can assist in detecting vehicles behind or to the side of your vehicle. Note: The detection area, collision The warning lamps to support this system are time threshold value and vehicle located within the LH and RH door mirror speed provided in the system function Note: The radar requires calibration glasses, they will illuminate or flash to warn of description are just for your reference. on new vehicles or for vehicles of an approaching object or car to assist you in where a rear detecting radar sensor manoeuvring the car safely. has been replaced. The rear detection radar sensors possess an automatic calibration function to compensate for installation error within a certain range. When the vehicle is running, the radar will automatically enter the calibration 177


key: chroma:document
string_value:
Starting & Driving Blind Spot Detection (BSD) 1 Rear driver assistance system is in the Lane Change Assist (LCA) ON state and no faults are present in the When the vehicle is driving forward, the When the vehicle is driving forward, the system. system will monitor the motor vehicles system will monitor the motor vehicles located in the blind zones of the left and right 2 Blind spot detection (BSD) function is approaching rapidly in the adjacent lanes. exterior mirrors. When the conditions for enabled. When the conditions for activating the lane activating the blind spot detection function are change assist function are met, the warning 3 The vehicle speed is above 30km/h. met, the warning lamps in the corresponding lamps in the corresponding mirror will mirror will illuminate. Subsequent operation 4 There are motor vehicles in the blind illuminate, once the indicators are activated, of the relevant indicator will cause the zone of the vehicle. The system monitors the warning lamps will flash to warn the warning lamp in the mirror to flash to remind both the left and right of the vehicle, driver of an approaching vehicle. This aims to the driver of an approaching vehicle. the monitored areas are 2m ahead , 7m help avoid collisions when changing lanes. behind the rear of the vehicle, and 4.7m from the side of the vehicle. Note: The warning lamps will not illuminate whilst you are overtaking another vehicle and your speed is greater than that of the vehicle you are passing, even though it is in the blind zone. The conditions for activating the blind spot detection function include: 178


key: chroma:document
string_value:
Starting & Driving The conditions for activating the lane change Rear Cross Traffic Alert (RCTA) 2 Rear cross traffic alert (RCTA) function is assist function include: enabled. When the vehicle is reversing, the system 1 Rear driver assistance system is in the will monitor vehicles approaching from the 3 The vehicle is in Reverse gear. ON state and no faults are present in the left and right rear. When the conditions for 4 The vehicle speed is less than 9km/h. system. activating RCTA function are met, the warning lamps in the mirrors on the corresponding 5 The speed of the vehicle being monitored 2 Lane change assist (LCA) function is side will illuminate, parking information will is above 9km/h. enabled. 4 be displayed in the infotainment screen to 6 The motor vehicle drives across the 3 The vehicle speed is above 30km/h. alert the driver to the situation. system detection areas. The areas 4 The speed of the approaching vehicle is monitored to the left and right of the higher than the speed of your vehicle. vehicle are 5m behind the rear of the vehicle, and 25m from the side. 5 The approaching vehicle enters the detection area of the LCA, the monitored 7 The approaching vehicle is likely to have areas are 7 - 70m behind your vehicle and a collision with your vehicle within 2.5 4.7 m to the side of your vehicle. seconds. 6 The approaching vehicle is likely to have a collision with your vehicle within 3.5 seconds. The conditions for activating the rear cross traffic alert function include: 1 Rear driver assistance system is in the ON state and no faults are present in the system. 179


key: chroma:document
string_value:
Starting & Driving Tyre Pressure Monitoring replace normal tyre maintenance. For tyre Load Carrying System (TPMS) * maintenance, please refer to ‘Tyres’ in ‘Maintenance’ chapter. DO NOT exceed the gross vehicle weight or the permitted TPMS can not replace routine front and rear axle loads. Failure maintenance and checks of tyre If the TPMS malfunction indicator may result in vehicle damage or condition and pressures. lamp illuminates, and the warning message serious injury. “XX Tyre Pressure Low” is accompanied Using equipment that transmits displayed, it is advised that you please stop Load Space on frequencies similar to that the car as soon as possible, check the tyre of the TPMS may interfere with the operation of the Tyre pressure and inflate the tyre to correct Ensure that the rear seat pressure value. Driving with under-inflated backrests are securely latched in Pressure Monitoring System, this tyres, the tyre will overheat and cause tyre the upright position when loads may illuminate a warning or fault. Using under-inflated tyres increase are carried in the load space register a temporary fault. more energy consumption and result in behind the seats. shorter tread life, and may affect vehicle Note: TPMS only warns of low tyre handling and braking performance. Always pressures, it does not re-inflate the tyre. If the boot lid (or tailgate) can check/adjust tyre pressures when they are not be closed due to the type of TPMS uses pressure sensors built into tyre cold. The tyre pressure label attached to the cargo loaded, be sure to close all valves to continuously monitor pressure vehicle indicates the correct amount of tyre windows during driving, select and transmit data to the ECU inside the inflation required for your vehicle when the the face distribution mode of the vehicle using RF signals. If it deduces that the tyre is cold. pressure of that tyre has fallen below the air condition, and set the blower predefined limit of the system, the warning TPMS Self-learning to maximum speed, so as to light in the instrument pack will illuminate decrease exhaust fumes entering When replacing a TPMS sensor and receiver, (always yellow). For more information, please the vehicle. or performing tyre rotation, TPMS self- refer to ‘Instrument Pack’ in ‘Instruments learning is required, please consult an MG and Controls’ section. TPMS can remind Authorised Dealer for details. you of low tyre pressure, but it can not 180


key: chroma:document
string_value:
Starting & Driving When luggage carried in the boot, always Internal Loading ensure heavy items are placed as low and as far forward as possible, so as to avoid the DO NOT carry unsecured cargo shift in the event of an accident or equipment, tools or luggage that sudden stop. could move, causing personal Drive carefully and avoid emergency braking injury in the event of an or maneuvers when large or heavy items are accident, emergency braking or 4 carried. hard acceleration. Driving with the boot lid (or tailgate) open is very dangerous. If the load being carried DO NOT obstruct the driver and passengers to keep right sitting requires the boot lid (or tailgate) to be open, please ensure the cargo and the boot lid posture and observation with (or tailgate) are suitably secured and every loads. measure is taken to prevent exhaust fumes Folding the rear seats can increase luggage entering the vehicle. space, refer to “Rear Seat” in “Seats and IMPORTANT Restraints” chapter. Traffic regulations must be observed when When cargo is loaded in the vehicle, place it loading cargo, if the cargo extrudes the at a position as low as possible and ensure loadspace, appropriate warning measures that it is tightly secured, so as to avoid must be taken to warn other road users. personal injury caused by cargo movement when traffic accidents or emergency brakes occur. If the cargo has to be put on a seat, no one is allowed to sit on that seat. 181


key: chroma:document
string_value:
Emergency Information Emergency Information Emergency Information ..........................183 Hazard Warning Devices ...................... 184 Emergency Starting ..................................184 Vehicle Recovery .....................................186 5 Wheel Replacement ................................188 Fuse Replacement ....................................192 Bulb Replacement ....................................196 183


key: chroma:document
string_value:
Emergency Information Hazard Warning Devices Warning Triangle Emergency Starting Hazard Warning Lights Using Booster Cables NEVER start the engine by pushing or towing. Make sure that BOTH batteries are of the same voltage (12 volts), and that the booster cables are approved for use with 12 volt car batteries. Ensure sparks and naked lights are kept well away from the Note: Before you stop or slow the engine compartment. car in an emergency, always press The warning triangle supplied with your car is Using booster cables (jump leads) from a the hazard warning switch. All the stowed in the loadspace. donor battery, or a battery fitted to a donor direction indicators will flash together If you have to stop your car on the road in an vehicle, is the only approved method of to warn other road users when your emergency, you must place a warning triangle starting a car with a flat battery. car is causing an obstruction or is in approximately 50 - 150 metres behind the a hazardous situation. Remember to If the battery from a donor vehicle is to be car, if possible, to warn other road users of switch off before driving away. used, the vehicles should be parked with their your position. battery locations adjacent to one another. Ensure that the two vehicles do not touch. 184


key: chroma:document
string_value:
Emergency Information Starting the Vehicle 1 Connect the RED booster cable between IMPORTANT the positive (+) terminals of both Ensure that each booster cable batteries. Connect the BLACK booster NEVER turn on any electrical equipment connection is securely made. cable from the negative (-) terminal of the on the started vehicle before removing the There must be no risk of the clips donor battery (A) to a good earth point booster cables. accidentally slipping from the (an engine mounting or other unpainted battery terminals (as a result of surface, for example), as far away from 5 Disconnecting the booster cables must engine vibration, for example), the battery as possible and well away be an exact reversal of the procedure this could cause sparking, which from fuel and brake lines on the disabled used to connect them, i.e. disconnect the vehicle (B). BLACK cable from the earth point on the could lead to fire or explosion. 2 Check that the cables are clear of moving disabled vehicle FIRST. 5 parts of both engines, then start the Note: It is recommended to ensure that engine of the donor vehicle and allow it the disabled vehicle runs for more than to idle for a few minutes. 1 hour after it is started, in order to 3 Now start the engine of the vehicle recover the battery power. with the discharged battery (DO NOT crank the engine for more than 10 seconds). If the disabled vehicle will not start after several attempts, it may need to be repaired. Please contact the MG Authorised Dealer. 4 After both the vehicles have normally started, allow the engines to idle for Ensure the START/STOP Switch is turned off more than 2 minutes before shutting and switch off ALL electrical equipment of down the engine of the donor vehicle and BOTH vehicles, then follow the instructions disconnecting the booster cables. below: 185


key: chroma:document
string_value:
Emergency Information Vehicle Recovery Note: The towing eye cover may be secured to the bumper by a plastic cord. Towing for Recovery Both towing points are intended for use by Towing Hook qualified recovery specialists to assist in the recovery of your car when a breakdown or DO NOT use a tow rope that is twisted - any accident occur, such as pulling your vehicle untwisting force could unscrew the towing onto the trailer, etc. They are not designed eye. for towing other vehicles, and must NEVER be used to tow a trailer or caravan. The car can be towed by using a soft rope, but a hard rod is preferred. Your car is equipped with a removable towing hook, that can be used at the front or the rear of your vehicle. The towing hook is stored in the tool kit beneath the loadspace floor when not in use. To fit the towing hook, first press one end of the small cover plate (the white dot in the figure above), then open the small cover plate after the other end is lifted, then screw the towing hook through the small hole into the threaded hole on the bumper beam (as shown in the figure). Ensure the towing eye is fully tightened. 186


key: chroma:document
string_value:
Emergency Information Towing for Recovery 1 Switch the START/STOP Switch to the ON position to enable the brake lights, If, due to an electrical fault, wipers and direction indicators to be potential safety hazards may operated if necessary. exist, it is not allowed to put the 2 If the battery power is low, please stop START/STOP Switch in the ON four-wheel touchdown towing and use position. other towing methods. 3 Place the shift lever in N position When towing, DO NOT suddenly (manual transmission), or in N position accelerate or brake suddenly, (automatic 5 transmission). this can cause accidents. 5 4 Release the parking brake. The towing speed of a vehicle 5 Turn on the hazard warning lamps. must not exceed 30 km/h, the towing distance shall not exceed 6 If the transmission is damaged or has a 50 km. lack of lubricating oil, DO NOT tow the vehicle with four wheels on the ground. Suspended Towing Four-Wheel Touchdown Towing 7 DO NOT tow backward with front If your car needs to be towed, most wheels (drive wheels) on the ground. qualified recovery specialists will use wheel DO NOT tow the vehicle lift equipment to suspend the front wheels, equipped with CVT with four while the rear wheels remain on the ground. wheels on the ground. This type Ensure the parking brake is released, the of vehicle can only be towed by hazard warning lamps are activated and no suspended towing, otherwise the Without the engine running, greater effort passengers are left in the vehicle. transmission may be damaged. may be required to operate the brake pedal If vehicle is towed with the four wheels on the and turn the steering wheel. Longer stopping ground, observe the following precautions: distances will also be experienced. 187


key: chroma:document
string_value:
Emergency Information Transporter or Trailer with Rope 3 Fit the lashing straps (3) around the Wheel Replacement wheels and secure to the trailer. Tighten If your car is to be transported on the back the straps until the car is securely held. Spare Wheel and Toolbox of a trailer or transporter, it must be secured as illustrated: Spare Wheel and Tool Removal 1 Lift the carpet in the trunk with the lifting strap (A). 1 Position the car on the trailer, apply the parking brake, and place the shift lever in 2 Remove the tool tray (B). N position (manual transmission), or in P 3 Unscrew the spare wheel retaining nut position (automatic transmission). and lift the spare wheel from the trunk. 2 Place the wheel chock (1) as shown in the figure, then place the anti slip rubber pad (2) around the circumference of the tyre. 188


key: chroma:document
string_value:
Emergency Information Spare wheel replacement tool Changing a Wheel Positioning the Jack If you need to change the wheel during the journey, choose a safe place to stop away NEVER work beneath the vehicle with the jack as the only means from the main thoroughfare if possible. Always ask your passengers to get out of of support. The jack is designed the vehicle and wait in a safe area away from for wheel changing only! other traffic. NEVER jack the vehicle using Switch on hazard warning lamps. If the any jacking points other than conditions permit, place a warning triangle the designated points shown. which is approximately 50 to 150 meters 5 1 Jack handle Otherwise serious damage to away behind the vehicle to warn other the vehicle could result. 2 Towing hook vehicles. 3 Wheel bolt cap removal tool Before changing a wheel, ensure the front wheels are in the straight ahead position. 4 Wheel bolt spanner Apply the parking brake, and place the shift 5 Jack lever in P position. Observe the following precautions: • Ensure the jack is positioned on firm, level ground. • If vehicles have to be parked on the hill, wedge-shaped bumpers shall be placed before/after the other three wheels to avoid the vehicle moving. 189


key: chroma:document
string_value:
Emergency Information Position the jack on firm level ground under Replacing with Spare Wheel Avoid the outer side of the wheel the jacking point nearest the wheel to be contacting the ground, and the rim removed. Make sure the rectangle slot of the Check the pressure of the spare surface may be scratched. jack must support the vehicle body revers wheel to avoid flat tyre as it is (see the figure). not used for a long time. Always 3 Remove the wheel bolts and place them Turning the jack screw rod handle by hand, check tyre pressures after in the toolbox to prevent them from being lost. Make sure the vehicle is steady raise the jack until the jack head fits snugly changing a wheel. and there is no risk of slip or movement on vehicle body revers. Ensure that the base before removing wheel bolts. of the jack is in full contact with the ground. After replacing the wheel, you must tighten the wheel bolts 4 Remove wheels. to the specified torque (120 ~ Note: Replace the spare wheel with 130Nm). the removed wheel and place it under 1 Before raising the vehicle, use the vehicle the vehicle body flanging area near the tool to remove each wheel bolt cap. Use jack. Avoid the outer side of the wheel the wheel spanner to slacken the bolt half contacting the ground, and the rim a turn anti-clockwise. surface may be scratched. 2 Turn the jack handle in a clockwise direction until the tyre is clear of the 5 Fit the spare wheel and tighten the wheel ground. bolts until the wheel is seated firmly against the hub. Note: For your safety, please put the 6 Lower the vehicle and remove the jack, spare tyre under the vehicle body then FULLY tighten the wheel bolts in a flanging area near the jack. diagonal sequence. 7 Finally, stow the tools back into the tool tray, and put the replaced wheel into the well under the trunk floor (with the wheel rim facing down). 190


key: chroma:document
string_value:
Emergency Information Note: DO NOT stand on the handle of Spacesaver Spare Wheel Note: DO NOT use an automatic car the wheel bolt spanner or use extension wash when the spacesaver wheel is tube on the handle of the spanner. Only one spacesaver spare fitted, the guide rails of the car wash wheel can be used at any one may conflict with the wheel/tyre and Note: When replacing the wheel, please time, otherwise the operational cause damage. fully tighten the bolts in the diagonal performance and brake sequence in 2 times. performance may be reduced, *Steel wheel is provided as spare wheel. thereby leading to accident or #Spare tyre can be from any manufacturer. Note: Contact an MG Authorised Dealer injury to yourself and others. to replace with a new tyre urgently. When driving on icy or slippery 5 surfaces it is advised to fit the spacesaver wheel to the rear of the vehicle to maintain adaquate stability. This may mean swapping a front wheel with a rear wheel. Snow chains can not be used on the spacesaver spare wheel, this can cause damage to the car and snow chain. When the spacesaver spare wheel is fitted, the vehicle speed should not exceed 80 km/h. Please have the full-scale tyre repaired and replace the spare wheel as soon as possible. This will extend the life span of the spare wheel for other emergencies. 191


key: chroma:document
string_value:
Emergency Information Fuse Replacement Fuse Box Passenger Compartment Fuse Box There are two fuse boxes in the vehicle: Fuse Fuses are simple circuit breakers which protect the vehicle electrical equipment by preventing the electrical circuits from being overloaded. A blown fuse indicates that the item of electrical equipment it protects stops working. Check a suspect fuse by removing it from the fuse box and looking for a break in the wire inside the fuse. Check or Replace a Fuse It is recommended to have spare fuses in the 1 Switch off the vehicle power system and vehicle, which can be obtained from a local 1 Front Compartment Fuse Box (at the left all electrical equipment, disconnect the MG Authorised Dealer. side of the Front Bay). battery negative cable. IMPORTANT 2 Passenger Compartment Fuse Box 2 Remove the closing panel below the (below the glove box at the front glove box to gain access to the fuse box. • NEVER attempt to repair a blown fuse. passenger side). ALWAYS replace a fuse with one of 3 Press the fuse extraction tool onto the the same rating. fuse head and pull to remove the fuse. A blown fuse can be recognised by a break • If a replaced fuse fails immediately, in the wire. please contact an MG Authorised Dealer as soon as possible. 4 Replace the blown fuse with a same rating. 192


key: chroma:document
string_value:
Emergency Information Fuse Specification No. Specs Function No. Specs Function Front Courtesy Front Central No. Specs Function Lamp, Outside Display, Front F24 20A Front Washer Relay, Mirror and Master Infotainment F1 15A Rear Washer Relay Light Height Adjust Control Module F16 5A F2 10A Diagnostic Socket Switch, Top USB, Automatic Left Headlamp F3 5A PRND Display F25 10A Temperature Assembly, Right Controller F4 - - Headlamp Assembly F26 5A Instrument Pack F5 10A Airbag ECU (SDM) F17 5A Rear USB 5 Transmission Keyless Start/Stop F18 5A EPB Switch F6 10A F27 10A Control Module-AT/ Switch, Gateway Outside Mirror and CVT Driver Seat Adjust Master Light Height F7 30A F19 5A Information Switch Adjust Switch, Rain F28 5A Faceplate Light Sensor F8–F9 - - F29 30A Sunroof Left Rear Driving F10 10A Voice Robot F20 5A F30 5A TBOX Assistance Radar F11– F14 - - F21 10A 360° View Module F31 5A Tyre Pressure Monitoring System Exterior Mirrors F15 15A Front Power Socket F22 10A Electronic Steering Heating Element F32 10A Column Lock Rear Windscreen F23 25A F33 30A Sunroof Heating Element 193


key: chroma:document
string_value:
Emergency Information Front Compartment Fuse Box Fuse Specification No. Specs Function F34– - - No. Specs Function F41 FL1 150A Alternator Stability Control F42 25A Module(Valve)-MT Electric Power FL2 80A Steering Module Stability Control F42 40A Module(Valve)-AT/ Cooling Fan Relay FL3 40A CVT Pack Passenger Window Windscreen/ F43 30A lift Switch, Rear Left Mirror Heating Window Lift Switch Relay, Passenger FL4 80A Check or Replace a Fuse Compartment Fuse Driver Door F18, F19, F20, F21, Switch Pack, Driver 1 Switch off the vehicle power system and F42, F43, F44 F44 30A Window Lifter, Rear all electrical equipment, disconnect the Right Window Lift battery negative cable. KLR Relay, Switch 2 Press the locating clips to remove the Passenger Compartment Fuse fuse box lid. FL5 80A F1, F2, F3, F4, F5, 3 Press the fuse extraction tool onto the F6, F7, F24, F25, fuse head and pull to remove the fuse. A F26, F27, F28, F29, blown fuse can be recognized by a break F30, F31, F32, F33 in the wire. FL6 - - 4 Replace the fuse with a same rating. Automatic FL7 40A Temperature Controller, Blower 194


key: chroma:document
string_value:
Emergency Information No. Specs Function No. Specs Function Ignition Coil, Engine F12 30A Control Module Body Control F4 10A Compressor Relay FL8 20A Module No. Specs Function Engine Control F5 5A Stability Control Module F13 15A Horn Relay FL9 40A Module(Pump) F6 10A Fuel Injector F14 - - FL10 - - Front Wiper Enable Intake Variable FL11 - - Relay, Front Wiper Camshaft Timing, F7 30A High/Low Speed Exhaust Variable FL12 - - Relay F15 10A Camshaft Timing, 5 FL13 30A Starter Relay Canister Purge Cooling Fan Relay FL14 - - Valve(1.5L), Oil Pack, Control Valve(1.3T) FL15 30A EVP Relay Pedal Switch, FL16 - - Fuel Pump Relay, F16 15A Rear Wiper Relay FL17 - - F8 5A AC Pressure F17 10A Fog Lamp Relay Switch, Neutral F18 5A Airbag ECU (SDM) Right Headlamp Switch(1.5L), F1 10A Assembly Canister Vent Instrument Pack, Downstream Valve(1.3T), EVP Front Detect Radar, Lambda Sensor, Relay(1.5L) Front View Control F19 5A Module, Shifter Upstream Lambda F9 20A Fuel Pump Relay Mechanism, Reverse F2 15A Sensor,Canister Right Headlamp Lamp Switch, Airbag Purge Valve(1.3T), F10 10A Assembly Display Module Purge Washer Pump(1.3T) Left Headlamp Engine Control F11 10A F20 5A Assembly Module Left Headlamp F3 10A Assembly 195


key: chroma:document
string_value:
Emergency Information Bulb Replacement Body Control F21 25A Module Bulb Specification F22 - - No. Specs Function Lamp Bulb Specifications License Plate W5W 5W F23 - - 100 LED Lamps F24 - - Front Direction Rear Fog Lamps LED LED Body Control Indicators High Mounted Stop F25 30A LED Module Daytime Running Lamp LED F26 - - Lamps Interior Lamp LED Body Control Front Side Light LED Load Space Lamp C10W 10W F27 15A Module Front Fog Lamps * H8 35W F28 - - Reverse Lamps W16W 16W F29 - - Rear Direction WY16W 16W Engine Control Indicators Module, Rear Side Light F30 5A Transmission (high configuration) LED Control Module- Stop Lamps (high CVT LED configuration) Rear Side Light W5W 5W (low configuration) Stop Lamps/ Rear Side Light (low W21/5W 21/5W configuration) 196


key: chroma:document
string_value:
Emergency Information Bulb Replacement Load Space Lamp Bulb Renewal Before replacing any bulb, turn off the START/ STOP Switch and lighting switch to avoid any possibility of a short circuit. Note: MG only recommends replacement bulbs that completely meet the manufacturers specifications. Take care NOT to touch the glass with your fingers; always use a cloth to handle the bulb. 1 Insert a suitable tool or small flat bladed 5 If necessary, clean the glass with methylated screwdriver into the indent on one of the spirits to remove fingerprints. narrow sides (as arrowed in figure) of the lens and carefully remove the unit from If in doubt, when replacing bulbs, contact an its location. MG Authorised Dealer. 2 Push while rotating the bulb to remove it. For replacement of other bulbs not listed please consult an MG Authorised Dealer. The bulb refit procedure is in reverse order with the bulb removal procedure. 197


key: chroma:document
string_value:
Maintenance Maintenance Maintenance ..............................................199 Routine Maintenance ..............................200 Bonnet .........................................................202 Engine Compartment ..............................204 Engine ..........................................................206 Cooling System ........................................207 6 Brake ..........................................................209 Battery ........................................................210 Washers .....................................................212 Wipers ........................................................213 Tyres ..........................................................215 Cleaning and Vehicle Care ....................218 199


key: chroma:document
string_value:
Maintenance Routine Maintenance Service History Emission Control The safety, reliability and performance of Ensure your local MG Authorised Dealer fills Your car is fitted with emission and your car will depend partly on how well in the Service Records after each service. evaporative control equipment designed it is maintained. You must ensure that to meet specific territorial and legal maintenance is carried out when required Brake Fluid Replacement requirements. Incorrect engine settings may and according to the information contained adversely affect exhaust emissions, engine Replace the brake fluid according to the in the ‘Service Schedule’. performance and fuel consumption, as well information contained in the “Service as causing high temperatures, which could Schedule”. Servicing result in damage to the catalytic converters and engine. For next service information, please refer Note: Brake fluid replacement will be to “Message Centre” in “Instruments and an additional cost. IMPORTANT Controls” chapter or information related to You should be aware that unauthorised entertainment system. After the completion Coolant Replacement replacement, modification or tampering of each service, the next service display will be reset by your MG Authorised Dealer. Replace the engine coolant (mixed solution with this equipment by an owner or of antifreeze and water) according to the motor vehicle Dealer could result in the Note: If a service is not carried out (or information contained in the “Service manufacturer’s warranty being deemed as the display is not reset by the local MG Schedule”. invalid. In addition, engine settings must not be tampered with. Authorised Dealer after service), the service display cannot provide correct Note: Coolant replacement will be an additional cost. information. 200


key: chroma:document
string_value:
Maintenance Owner Maintenance • Windscreen washer fluid level. Safety in the Garage • Operate air conditioning. Any significant or sudden drop in Cooling fans may commence fluid levels, or uneven tyre wear, Note: The engine oil level should be operating after the engine should be reported without checked more frequently if the car is is switched off, and continue delay. For further information, driven for prolonged periods at high operating for a number of refer to an MG Authorised speeds. minutes. Keep clear of all fans Dealer. while working in the engine compartment. Special Operating Conditions In addition to the routine services referred to previously, a number of simple checks must If your car is frequently used in dusty If you need to carry out maintenance, observe be carried out more frequently. You can conditions, or operated in extreme climates the following safety precautions at all times: carry out these checks yourself and advice is where sub-zero or very high ambient • Keep your hands and clothing away from given on the pages that follow. temperatures are normal, more frequent drive belts and pulleys. 6 attention may need to be paid to servicing Daily Checks requirements. You need to carry out special • If the car has been driven recently, DO • Operation of lights, horn, direction maintenance operations (refer to Service NOT TOUCH exhaust and cooling indicators, wipers, washers and warning Portfolio or contact your MG Authorised system components until the engine has lights. Dealer). cooled. • Operation of seat belts and brakes. • DO NOT TOUCH electrical leads or components while the engine is running, • Look for fluid deposits underneath the or with the ignition switch on. car that might indicate a leak. • NEVER leave the engine running in an • Check tyre appearance. Weekly Check unventilated area - exhaust gases are • Engine oil level. poisonous and extremely dangerous. • Coolant level. • DO NOT work underneath the car with • Brake fluid level. a wheel changing jack as the only means of support. 201


key: chroma:document
string_value:
Maintenance • Ensure that sparks and naked lights are Used Engine Oil Bonnet far away from the engine compartment. Prolonged contact with engine oil may cause Opening the Bonnet • Wear protective clothing and work serious skin disorders, including dermatitis gloves. and cancer of the skin. Wash thoroughly after DO NOT drive when the bonnet is • Remove watches and jewelry before contact. Used engine oil should be disposed not closed or retained only by the of correctly. Incorrect disposal can cause a working in the engine compartment. safety catch. threat to the environment. • DO NOT allow tools or metal parts of the car to make contact with the battery leads or terminals. Toxic Liquid Fluids used in motor vehicles are poisonous and should not be consumed or brought into contact with open wounds. These include: battery acid, coolant, brake fluid, power steering fluid, fuel, engine oil and windscreen washer additives. For your own safety, ALWAYS read and 1 From the inside of the vehicle, pull the observe all instructions printed on labels and bonnet release handle (Figure A). containers. 2 Move the safety catch release handle on the bonnet lock assembly in the direction of the arrow (Figure B) to release the bonnet safety catch. 3 Raise the bonnet and hold it up with the support rod firmly. 202


key: chroma:document
string_value:
Maintenance Closing the Bonnet IMPORTANT Support the bonnet by one hand, release the • For safety reasons, the bonnet support rod using the other hand, and place should be fully latched and secure it firmly into the support rod base. Then hold when driving. Therefore every time the bonnet using both hands and lower it, the bonnet is opened, you must allowing it to drop for the last 20 cm ~ 30 cm check after closing that the bonnet is to fully close the bonnet. securely latched, e.g. the bonnet edge is flush with the body of the car. By attempting to lift the front edge of the • You should stop the car immediately bonnet, check if the lock is fully engaged after when safety permits and close the closing the bonnet. If it is not fully engaged, bonnet if it is not closed fully when you must repeat the operation. driving. Bonnet Open Warning • Ensure the bonnet is supported 6 manually when removing the bonnet If the bonnet is not fully engaged, when support rod, failure to support the the vehicle power system is in the ON/ panel will result in the panel falling RUNNING position, the corresponding down causing injury or vehicle damage. alarm icon will be displayed in the information message centre of the instrument pack. If it is • Beware of injury to hands while fully detected that the bonnet is not fully engaged closing the bonnet with a downward whilst driving, an audible warning will sound. force. 203


key: chroma:document
string_value:
Maintenance Engine Compartment 1.5L Engine Compartment While working in the engine compartment, always observe the safety precautions listed under ‘Safety in the Garage’, refer to ‘Maintenance’ in ‘Maintenance’ section. 1 Washer fluid reservoir (blue cap) 2 Engine oil filler cap (black cap) 3 Brake fluid reservoir (yellow/black cap) 4 Engine oil dipstick (yellow) 5 Coolant reservoir (black cap) 204


key: chroma:document
string_value:
Maintenance 1.3L Turbocharged Engine Compartment While working in the engine compartment, always observe the safety precautions listed under ‘Safety in the Garage’, refer to ‘Maintenance’ in ‘Maintenance’ section. 1 Washer fluid reservoir (blue cap) 2 Engine oil filler cap (black cap) 3 Brake fluid reservoir (yellow/black cap) 4 Engine oil dipstick (yellow) 5 Coolant reservoir (black cap) 6 205


key: chroma:document
string_value:
Maintenance Engine Engine Oil Level Check and Top Up Engine Oil Driving the vehicle with the engine oil level ABOVE the ACEA Classification of Engine Oils upper mark, or BELOW the lower mark on the dipstick, will The European Automobile Manufacturers damage the engine. Take care to Association (ACEA) classifies the engine avoid spilling engine oil onto a oils based on their performance and quality. To ensure the best performance of the hot engine – a fire may result! vehicle, please use the ACEA C2 engine oil recommended by the manufacturer. Choose the oil viscosity according to the ambient temperature. If the temperature change is minimal, continue using the oil of original viscosity. 1.5L Engine In normal temperature, we advise you to use the SAE Check the oil level weekly and top up with oil 5W-30 engine oil recommended by the when necessary. Ideally, the oil level should manufacturer. be checked with the engine cold and the car resting on level ground. However, if the If you are using your vehicle in an extreme engine is running and already getting warm, cold region, we advise you to use the SAE wait for at least five minutes after switching 0W-30 engine oil recommended by the off the START/STOP Switch before checking manufacturer. 1.3L Turbocharged Engine the level. 1 Withdraw the dipstick and wipe off the oil on it. 206


key: chroma:document
string_value:
Maintenance 2 Slowly insert the oil dipstick and pull it Engine Oil Specification Cooling System out again to check the oil level; the oil Use the engine oil recommended and level shall not be lower than the “MIN” Coolant Check and Top Up certified by the manufacturer. Refer to mark on the oil dipstick. “Recommended Fluids and Capacities” in 3 Screw off the oil filler cap and refill the “Technical Data” section. DO NOT remove the coolant oil to maintain the oil level between the pressure cap when the cooling “MAX” mark and “MIN”mark on the oil Note: Do not use the oil additives not system is hot - escaping steam or dipstick. applicable to the car, or else the engine hot coolant could cause serious may be damaged. You are recommended injury. 4 Wait for 5 minutes and then recheck the to use the oil additives certified by the oil level, add an appropriate amount of oil if necessary – DO NOT OVERFILL! manufacturer, please consult your local Authorised Dealer for details. 5 Finally, ensure the dipstick is inserted and oil filler cap is fully secured. IMPORTANT 6 Check the engine oil level more frequently if the vehicle is driven at high speed for prolonged periods. The cooling system should be checked weekly when the cooling system is cold and with the car resting on level ground. If the coolant level is below the “MIN” mark, open 207


key: chroma:document
string_value:
Maintenance the coolant expansion tank cap and top up Coolant Specification coolant. The coolant level should not be Prevent the coolant from Please use the coolant which is recommended higher than the “MAX” mark. coming into contact with the and certified. Please refer to ‘Recommended skin or eyes. If this occurs, rinse Fluids and Capacities’ in the “Technical Data” Note: Prevent coolant from coming immediately with plenty of section. into contact with the vehicle body when water. If eyes are still red, painful topping up. Coolant will damage paint. Note: The addition of corrosion or uncomfortable, seek medical inhibitors or other additives to the attention immediately. If the coolant level falls appreciably during a cooling system of this car may severely short period, and you suspect that there may disrupt the efficiency of the system and be a leak, please seek an Authorised Dealer for service. cause parts damage. For cooling system issues please consult an Authorised Dealer. Coolant is poisonous and can be fatal if swallowed - keep coolant containers sealed and out of the reach of children. If accidental contact of coolant by children is suspected, seek medical assistance immediately. 208


key: chroma:document
string_value:
Maintenance Brake Brake Fluid Check and Top Up Note: Do not allow the brake fluid level to drop below the “MIN” mark or rise Brake Pads Brake fluid is highly toxic, above the “MAX” mark. keep containers sealed and out of the reach of children. DO NOT rest your foot on the If accidental contact of brake brake pedal while driving; this fluid is suspected, seek medical may overheat the brakes, reduce attention immediately. their efficiency and cause excessive wear. Prevent brake fluid coming For the first 1500 km, you should avoid into contact with the skin situations where heavy braking is required. or eyes. If this occurs, rinse immediately with plenty of Remember that regular servicing is vital to 6 water. If eyes are still red, painful ensure that all the brake components are or uncomfortable, seek medical examined for wear at the correct intervals, attention immediately. and replaced when required to ensure long term safety and optimum performance during Note: Brake fluid will damage painted The brake fluid level should be checked the interval prescribed in Service Portfolio. surfaces. If you accidentally spill the weekly when the system is cold and with the brake fluid on the painted surface, soak The car needs to run in for 800 km after the car on level ground. up any spillage with an absorbent cloth brake pad or disc is replaced. The brake fluid level can be seen through the immediately and wash the area with reservoir and should be maintained between water or car shampoo. the “MAX” and “MIN” marks. 209


key: chroma:document
string_value:
Maintenance Brake Fluid Specification Battery Use the brake fluid recommended and Battery Maintenance approved by the manufacturer. Refer to “Recommended Fluids and Capacities” in the DO NOT leave electric “Technical Data” section. components switched on when the vehicle is not in READY IMPORTANT mode, otherwise the battery Replace brake fluid regularly according to may become flat, resulting in the the Service Portfolio. failure to start the vehicle and the reduction of battery life. Always store batteries upright, tilting may allow the corrosive substances contained within the battery to leak out. The battery is located in the front Never attempt to dismantle a compartment and is maintenance-free, battery, they are sealed units. therefore there is no need to refill fluid. For different battery types equipped, on the top of some batteries there is a battery condition indicator. Examine the indicator periodically to check the battery’s condition. When the indicator shows: • GREEN - the battery is in a good state of charge. • DARK (turning to black) - the battery needs charging. 210


key: chroma:document
string_value:
Maintenance • CLEAR (or light yellow) - the battery Battery Replacement must be replaced. Note: Please ensure a clear view of The battery contains sulphuric acid, which is corrosive. the condition indicator. Use a torch if natural light is poor. The battery contains sulphuric acid, which is corrosive. Please go to an MG Authorised Note: It is recommended to start the Dealer to remove and install the battery. vehicle for half an hour every week Only fit a replacement battery of the same to help extend the service life of the type and specification as the original to battery. If the vehicle is stored for more maintain the correct vehicle functionality. than 1 month, remove the negative terminal from the battery. Make sure The battery must be disposed of using that the vehicle power system has an approved method, used batteries can be 6 been turned off before connecting or harmful to the environment. It should be disconnecting the negative terminal. recycled by a professional company. Please consult an MG Authorised Dealer for more details. 211


key: chroma:document
string_value:
Maintenance Washers Note: DO NOT use anti-freeze or IMPORTANT vinegar/water solution in the washer • Use the washer fluid recommended Windscreen Washer Check reservoir - anti-freeze will damage and certified by the manufacturer. and Top Up paintwork while vinegar will damage Misuse of washer fluid in winter may the washer pump. cause damage to the washer pump due Windscreen washer fluid is to freezing. flammable. DO NOT allow • Using the washers when there is no windscreen washer fluid to come washer fluid may cause damage to the into contact with naked flames washer pump. or sources of ignition. • Operating the wipers when the windshields are dry and there is no When filling the washer fluid, washer fluid may cause damage to the DO NOT let the washer fluid spill windshields and wipers. Please spray the washer fluid and start the wipers on parts in the compartment or when there is adequate washer fluid. on the paint surface of vehicle body. In case the washer fluid is spilled on hands or other parts Washer Nozzles of the body, please immediately Operate the washers periodically to check wash with clean water. that the nozzles are clear and properly directed. Check the washer fluid level regularly. When the level of washer fluid is low, please top If the nozzle is obstructed, insert a needle or up the washer fluid as instructed. Use the thin metal wire into the hole to remove the washer fluid recommended and certified by obstruction. the manufacturer. Refer to ‘Recommended Fluids and Capacities’. 212


key: chroma:document
string_value:
Maintenance Wipers Replacing Front Wiper Blades 3 Press the retaining clips at both sides (Without frame) * (as shown in the figure), whilst pulling Wiper Blades the wiper blade outward, to remove the wiper blade from the wiper arm and IMPORTANT discard. • Grease, silicon and petrol based products 4 Position the fitting of the new wiper blade impair the blade’s wiping capability. Wash into the slot of the wiper arm. the wiper blades in warm soapy water 5 Push the wiper blade towards the wiper and periodically check their condition. arm until it is located embedded with a • Clean the windscreen frequently, DO click been heard. NOT use wipers to remove stubborn or ingrained dirt, it will reduce their effect 6 Place the wiper assembly back on the and their life span. windscreen. • If signs of hardness or cracking in the 7 To exit the service mode and return the 6 rubber are found, or if the wipers leave wipers to the park position, operate the streaks or unwiped areas on the screen, wiper stalk switch again by pressing down then the wiper blades should be replaced. and releasing, alternatively, turn on the • Clean the windscreen regularly with an 1 With the bonnet closed, and within 20 START/STOP Switch. approved glass cleaner and ensure the seconds of switching the START/STOP screen is thoroughly cleaned before Switch to the OFF position, operate fitting replacement wiper blades. the wiper stalk switch by pressing down • Only fit replacement wiper blades that and releasing, the wipers will sweep are identical to the original specification. and stop in the ‘service position’ on the • Clean ice and snow from around wipers windscreen. and ensure they are not frozen or 2 Lift the wiper arm away from the otherwise sticking to the windscreen windscreen. before attempting to operate them. 213


key: chroma:document
string_value:
Maintenance Replacing Front Wiper Blades downward, to remove the wiper blade Replacing Rear Wiper Blades (With frame)* from the wiper arm and discard. 4 Put the fitting on new wiper blade into the U slot of the wiper arm. 5 Push the wiper blade upward until the it is fully embedded with a click been heard. 6 Place the wiper assembly back on the windscreen. 7 To exit the service mode and return the wipers to the park position, operate the wiper stalk switch again by pressing down and releasing, alternatively, turn on the START/STOP Switch. 1 Lift the wiper arm away from the rear 1 With the bonnet closed, and within 20 window. seconds of switching the START/STOP 2 Rotate the wiper blade as shown in the Switch to the OFF position, operate figure, to remove it from the wiper arm the wiper stalk switch by pressing down and discard. and releasing, the wipers will sweep and stop in the ‘service position’ on the 3 Position the fitting of the new wiper blade windscreen. into the slot of the wiper arm. Ensure the 2 Lift the wiper arm away from the wiper blade is properly secured on the windscreen. wiper arm. 3 Rotate the wiper blade and press 4 Place the wiper assembly back on the the retaining clip (as shown in the rear window. figure), meanwhile pull the wiper blade 214


key: chroma:document
string_value:
Maintenance Tyres New Tyres Tyre Life New tyres may not have the best adhesive Correct tyre pressure and moderate driving Overview ability at the beginning. Therefore, driving style can extend tyre life. • Take extra care when using new tyres for your vehicle at moderate speed and in a the first 500 kilometres. prudent way at the first 500 kilometres, Recommendations: • Avoid excessive cornering at speed. which is also beneficial to the service life of • If the vehicle is to be stored for a lengthy the tyres. time, please move your vehicle at least • Slow down when passing through road The damage of tyre or rim may happen once in two weeks to ‘rotate the tyres’. shoulder or a similar section, and allow the wheels to go through the shoulder at unnoticed. If abnormal vibration or handling • Check the pressure of tyres regularly the right angle as far as possible. is experienced, that means the tyre or rim when they are cold. may have been damaged. Please slow down • Regularly check the damage of tyres and park your vehicle in absolute safety, then • Avoid cornering at excessive speed. (stabs, scratches, cracks and pits) and check the tyre and rim. If you can’t see the • Regularly check tyres for abnormal wear 6 remove any foreign objects from the damage from the outside, you should continue patterns. These following factors may tread. to drive with low speed and go to the nearest affect the tyre life. MG Authorised Dealer for inspection. • Prevent the tyre from contacting oil, grease and fuel. Directional Tyres • Ensure valve caps are always fitted. Directional tyres are marked with ‘direction • If the tyre is to be removed always mark of rotation’ (DOR). To maintain handling the tyre/wheel orientation to ensure characteristics, tyre performance, low road correct reinstallation. noise and extend tyre life, tyres must always • The wheels or tyres that have been be fitted with indication arrow showing the disassembled should be kept in a cool, correct ‘DOR’. dry and light-free place. 215


key: chroma:document
string_value:
Maintenance Tyre Pressure Wheel Alignment Tyre Pressure Incorrect pressure will cause the abnormal Incorrect wheel alignment can cause wear of the tyre, greatly shorten the service excessive tyre wear and affect vehicle safety. Before a long distance journey, the tyre pressure must be life, and have an adverse effect on the driving If the tyres show signs of abnormal wear, characteristics of the vehicle. Tyre pressure seek advice from an MG Authorised Dealer. checked. should be checked at least once a month, and Check the pressure (including the spare once prior to each long-distance journey. Caring for Your Tyres wheel) at least once a month, when the tyres are cold. Driving Style DEFECTIVE TYRES ARE If it is necessary to check the tyre pressure Excessively harsh acceleration and braking, DANGEROUS! DO NOT when they are warm, you should expect the you may hear a piercing noise) or driving at drive if any tyre is damaged, is pressure to have increased by 0.3 to 0.4 bar high speed whilst cornering will increase the excessively worn, or is inflated to (4.35 to 5.8 psi). In this circumstance, NEVER wear of tyre. an incorrect pressure. let air out of the tyres in order to match the recommended pressure (cold). Wheel Balance Always drive with consideration for the condition of the tyres, and regularly inspect Valves The working balance of auto-wheels is well the tread and side walls for any sign of tested before a new vehicle comes out of the distortion (bulges), cuts or wear. Keep the valve caps screwed down firmly factory. But the wheels may be out of balance - they prevent dirt from entering the valve. due to many factors. Note: If possible, protect tyres from Check the valve for leaks (listen for a tell-tale contamination by oil, grease and fuel. hissing) when you check the tyre pressure. If wheels are out of balance, shaking or vibration of the steering mechanism may occur and the tyres may be excessively worn. It is important to rectify this quickly. Each wheel should be rebalanced after installing a new tyre or having the tyre repair. 216


key: chroma:document
string_value:
Maintenance Punctured Tyres Replacement Tyres If a sharp object penetrates the tyre and remains in it, the tyre may not leak. If you It is recommended to install are aware of this occurring, reduce speed the tyres consistent with the immediately and drive with caution until original specifications. DO NOT the spare wheel can be fitted, or repairs replace the tyres with tyres of undertaken. any other type. Alternative tyres, of a different specification, may Note: If the sidewall of the tyre is adversely affect the vehicle’s damaged or distorted, replace the tyre driving characteristics and safety. immediately, do not attempt a repair. IMPORTANT In order to make your driving and safety better guarantee, it A tyre MUST be replaced as soon as a Tyre Wear Indicators wear indicator becomes visible. is suggested that you consult an 6 At the bottom of the original tyre, there is a MG Authorised Dealer. 1.6 millimeter high wear mark perpendicular to the wheel rolling direction. These Always have replacement wheels and tyres indicators moulded into the tread pattern at balanced before use. several points around the circumference. A Wheel Fitment Rotation mark on the side of a tyre, such as the upper case letter TWI or the triangle, indicating the It is not recommended that you swap wheels position of the wear mark. from side to side or front to rear in order When the tread has worn down to 1.6 to equalise tyre wear. Your vehicle is fitted millimeter, the indicators will come to the with Tyre Pressure Monitoring System which surface of the tread pattern, producing the means that each wheel is programmed to the effect of a continuous band of rubber across relative position. the width of the tyre. 217


key: chroma:document
string_value:
Maintenance Cleaning and Vehicle Care External Car Observe all safety precautions Washing Your Car on cleaning products; do not drink fluids and keep them away Some high pressure cleaning from the eyes. systems will penetrate door, window and sunroof seals, and damage lock mechanisms. DO NOT aim water jets directly at components that might be easily damaged. Do not clean the engine If you do wish to swap wheels and tyres compartment with high pressure around on the vehicle please consult an MG water since it may damage the Authorised Dealer as extra coding will be electrical system of the vehicle. required. In order to preserve the paint finish on your car, please observe the following care points: • DO NOT use hot water to wash the car. • DO NOT use detergents or washing up liquid. • In hot weather, DO NOT wash the car in direct sunlight. • When using a hose, DO NOT aim the water directly at window, door or sunroof seals, or through wheel apertures onto the brake components. 218


key: chroma:document
string_value:
Maintenance If the car is particularly dirty, use a hose to Cleaning with a High Pressure Cleaner IMPORTANT flush grime and grit from the bodywork, prior to washing. Then, wash the car using cold or • Avoid cleaning the vehicle in direct Note: Always read the manufacturers lukewarm water containing a good quality sunlight. operating instructions. wash and wax shampoo. Always use plenty of • When cleaning the vehicle in winter water to ensure that grit is flushed from the avoid spraying water directly onto When using high pressure washers, always surface and not ground into the paintwork. door locks and panel gaps due to risk ensure there is adequate distance between After washing, rinse the bodywork with clean of icing. the spray nozzle and any soft materials, decals water and dry off with a chamois leather. or rubber seals. • Do not use rough sponges or cloth to clean the car, this will damage the Cleaning the underside IMPORTANT paintwork finish. • Please pay attention to the operating Note: DO NOT use a high pressure hose • When cleaning the headlamps do not instructions of high pressure cleaner. to clean the engine compartment – use a dry cloth or sponge, use only damage to the car’s electronic systems warm soapy water. • Soft parts on the vehicle should be 6 kept in a large enough distance from may occur. • Make sure no loose material (Cloth the high pressure cleaner. From time to time, but particularly during or other inflammable material etc) is winter months when salt has been used on left (but not limited to) inside engine the roads, use a hose to wash the underside compartment / Engine Cover / Fender of the car. Flush away accumulations of mud after washing. and thoroughly clean those areas where debris can easily collect (wheel arches and panel seams, for example). 219


key: chroma:document
string_value:
Maintenance Removing Tar Spots Polishing the Paintwork Wiper Blades Use white spirit to remove tar spots and Wash in warm soapy water. DO NOT use DO NOT use car polish stubborn grease stains from the paintwork. spirit or petrol based cleaners. containing coarse abrasives – Then wash the area immediately with soapy these will remove the paint film water to remove all traces of the spirit. and damage the gloss finish. Windows and Mirrors Regularly clean all windows, inside and out, Body Protection Occasionally treat the paint surface with using an approved glass cleaner. an approved polish containing the following After washing, examine the paintwork for properties: Windscreen: In particular, clean the outside damage. If the damage has revealed bare metal, use a colored primer first, then apply • Very mild abrasives to remove surface of the screen with glass cleaner after washing the correct colour base coat and finish off with contamination without removing or the car with wash and wax products, and a lacquer pencil, if appropriate. Carry out this damaging the paint. before fitting new wiper blades. treatment after washing but before polishing • Filling compounds that will fill scratches Rear screen: Clean the inside with a soft or waxing. More extensive damage to paint and reduce their visibility. cloth, using a side to side motion to avoid or bodywork must be repaired in accordance with the manufacturer’s recommendations. • Wax to provide a protective coating damaging the heating elements. Failure to do this will invalidate the Anti- between the paint and the elements. Note: DO NOT scrape or use abrasive Corrosion Warranty. If in doubt, ask your Note: If possible, avoid applying polish cleaners on the inside of the rear screen MG Authorised Dealer. or wax products to window glass and – this will damage the heating elements. rubber seals. Mirrors: Wash with soapy water. Use a plastic scraper to remove ice. DO NOT use abrasive cleaning compounds or metal scraper. 220


key: chroma:document
string_value:
Maintenance Plastic Components Wheels Cleaning the Interior Any plastic components should be cleaned When cleaning the wheels any Plastic materials using conventional cleaning methods and not materials or water that contact be treated with abrasive materials. the brake disc directly may effect Clean plastic-faced materials with diluted upholstery cleaner, then wipe with a damp braking efficiency. cloth. Paint Damage In order to ensure the wheels are kept in Any paint damage or stonechips should be optimum condition they should be cleaned Note: DO NOT polish dashboard treated with suitable paint/lacquer materials regularly. components – these should remain non- immediately to avoid invalidating the Anti reflective. Only use a recommended non-acidic Corrosion Warranty. propriety wheel cleaner. Always read the Carpet and fabrics instructions on the product. Weather Strips and Rubber Seals Clean with diluted upholstery cleaner - test a concealed area first. 6 Any weather strips or rubber aperture seals should be treated with suitable materials Leather (silica gel) if they are cleaned using strong detergents, this should avoid any sticking and Clean leather trim with warm water and maintain the service life of the seal. a non-detergent soap. Dry and polish the leather with a dry, clean, lint-free cloth. Note: DO NOT use petrol, detergents, furniture creams or polishes as cleaning agents. 221


key: chroma:document
string_value:
Maintenance Instrument Pack, Audio and Airbag Module Covers Seat Belts Navigation Display DO NOT allow these areas to be DO NOT use bleaches, dyes Clean with a dry cloth only. DO NOT use flooded with liquid and DO NOT or cleaning solvents on seat cleaning fluids or sprays. use petrol, detergent, furniture belts. cream or polishes. Extend the belts, then use warm water and a To protect damage to the airbag SRS, the non-detergent soap to clean. Allow the belts following areas should be cleaned sparingly to dry naturally; DO NOT retract them or with a damp cloth and upholstery cleaner use the car until they are completely dry. ONLY: • Steering wheel centre pad. • Area of dashboard containing the passenger airbag. • Area of roof lining and front pillar finishers which enclose the side head impact protection modules. 222


key: chroma:document
string_value:
Technical Data Technical Data Technical Data ...........................................223 Technical Data Dimensions ...................224 Weights .......................................................226 Major Parameters of Engine ..................227 Recommended Fluids and Capacities ...228 Wheel Alignment (Unladen) .................229 Wheels and Tyres ....................................229 Tyre Pressure (Cold) ..............................229 7 223


key: chroma:document
string_value:
Technical Data Technical Data Dimensions Item, Units Parameter Overall length A, mm 4323 Overall width B, mm 1809 Overall height C (unladen), mm 1628 (excluding luggage rack) / 1650 (including luggage rack) Wheelbase D, mm 2585 Front Overhang E, mm 901 Rear Overhang F, mm 837 224


key: chroma:document
string_value:
Technical Data Item, Units Parameter Front wheel track, mm 1526 Rear wheel track, mm 1536 Minimum ground clearance (laden), mm 154 Minimum turning circle diameter, m 11.2 Fuel tank capacity, l 48L (MT/CVT) / 45L (AT) Note: Vehicle length not including the license plate. Note: Rearview mirrors and the deformed portion of tyre wall directly above the touchdown point are not included in the total width. 7 225


key: chroma:document
string_value:
Technical Data Weights Parameter Item, Units VTi - TECH (5MT) VTi - TECH (CVT) 220 TURBO (6AT) Person in Cab, person 5 5 5 Unladen Vehicle weight 1245 / 1264 / 1271 / 1303 1301 / 1315 / 1349 1324 / 1355 (kerb), kg Gross Vehicle weight, 1678 / 1696 / 1703 / 1736 1733 / 1748 / 1780 1756 / 1788 kg Unladen Front Axle 740 / 752 / 755 / 771 785 / 794 / 811 799 / 814 weight, kg Unladen Rear Axle 505 / 511 / 516 / 532 516 / 521 / 538 525 / 541 weight, kg Laden Front Axle 847 / 859 / 862 / 878 892 / 901 / 917 905 / 921 weight, kg Laden Rear Axle 831 / 837 / 842 / 858 841 / 847 / 863 851 / 867 weight, kg Ground Clearance 151 152 141 (mm - Laden condition) 226


key: chroma:document
string_value:
Technical Data Major Parameters of Engine Parameter Vehicle VTi - TECH (5MT) / CVT 220 TURBO (6AT) Bore × Stroke, mm × mm 75×84.8 80×89.4 Capacity, Litres 1.498 1.349 Compression Ratio 11.5:1 10:1 Fuel Type INDIA 91 unleaded gasoline and above INDIA 91 unleaded gasoline and above 7 227


key: chroma:document
string_value:
Technical Data Recommended Fluids and Capacities Capacity Name Grade VTi - TECH (5MT) VTi - TECH (CVT) 220 TURBO (6AT) Engine oil (after-sales C2 5W-30 4.1 4.6 replacement), L Engine Coolant, L ELC 4600 (GLYCOL OAT) 5.4 6.4 Automatic Transmission oil, L ENEOS AW - 1 - 6.2 Continuously variable Shell SL-2100 - 6.96 - automatic Transmission oil, L Manual Transmission oil, L Castrol BOT503 1.8 — Brake Fluid, L DOT 4 0.85 Air conditioning refrigerant, g R134a 540±20 *Specification may vary depending on vehicle manufacturing date. Please contact MG Authorized Workshop for exact specification of lubes / oils / fluids in your vehicle. 228


key: chroma:document
string_value:
Technical Data Wheel Alignment (Unladen) Spare Tyre Item Parameter Wheel Rim specification 6.5J×16 Camber -0°28’±45’ Spare Tyre specification 215/60 R16 Kingpin Castor 3°54’±45’ Front Toe in (Total) 0°8’±15’ Tyre Pressure (Cold) Kingpin Inclination 11°49’±45’ Camber -1°15’±45’ Wheels Unladen Rear Toe in (Total) 0°24’±20’ Front Wheels 230kPa/2.3bar/32psi Rear Wheels 230kPa/2.3bar/32psi Note: It is recommended that the pressure of spare tyre should be consistent Wheels and Tyres with that of main tyre. Wheel size 7J×17 6.5J×16 Tyre size 215/55 R17 215/60 R16 7 229


key: chroma:document
string_value:
Delivery of your vehicle DELIVERY OF YOUR VEHICLE Dealer Name................................................................................................. Dealer Address........................................................................................................................ FIRST NAME .......................................................................................................................... SURNAME ........................................................................................................ MODEL .................................................................................................................................................................................................................................................................................. VEHICLE DELIVERED ON .................................................................................................... BY ................................................................................................................. PRESENTATION AND EXPLANATION 1 FRONT OF THE VEHICLE 5 DRIVING POSITION Eg. Servicing details, Checking the levels Eg. Adjusting the driving position. Use of the instrument panel and controls. Specific points relating to your vehicle. 2 FRONT PASSENGER SIDE Eg: Programming the radio, bluetooth, automatic illumination Eg. Disconnecting the passenger airbag (to fit a child seat of the headlights, etc. to the front seat) 3 REAR OF THE VEHICLE 6 DEALER SERVICE DEPARTMENT Eg. Location of the spare wheel, tool kit 7 WARRANTY AND MAINTENANCE CONDITIONS 7 4 REAR SEATS Eg. Warranty and maintenance documents (Service sheet or Eg. Child safety (lsofix fixing point) Modularity of the seats warranty & maintenance booklets), maintenance stamps 8 ISSUED WITH » Was your vehicle presented to you as stated above? Two set of keys YES NO Tool kit » Did your vehicle match your vehicle order? Spare tyre Vehicle invoice YES NO Insurance cover note Registration document Vehicle manual 231


key: chroma:document
string_value:
Delivery of your vehicle Comments: .................................................................................................................................................................................................................................................................. .................................................................................................................................................................................................................................................................. .................................................................................................................................................................................................................................................................. Please note that MG Motor India will not be responsible for any issues pertaining to Non Genuine Accessories fitted either by dealership or aftermarket. Should you require any further details regarding the vehicle handover or if you have any questions relating to your vehicle, please do not hesitate to contact your Sales or Delivery Advisor. ENJOY DRIVING YOUR NEW MG! CUSTOMER SIGNATURE DELIVERY ADVISOR SIGNATURE 1st EXEMPLARY: CUSTOMER 2nd EXEMPLARY: DELIVERY ADVISOR 232


key: chroma:document
string_value:
Delivery of your vehicle DELIVERY OF YOUR VEHICLE Dealer Name................................................................................................. Dealer Address........................................................................................................................ FIRST NAME .......................................................................................................................... SURNAME ........................................................................................................ MODEL .................................................................................................................................................................................................................................................................................. VEHICLE DELIVERED ON .................................................................................................... BY ................................................................................................................. PRESENTATION AND EXPLANATION 1 FRONT OF THE VEHICLE 5 DRIVING POSITION Eg. Servicing details, Checking the levels Eg. Adjusting the driving position. Use of the instrument panel and controls. Specific points relating to your vehicle. 2 FRONT PASSENGER SIDE Eg: Programming the radio, bluetooth, automatic illumination Eg. Disconnecting the passenger airbag (to fit a child seat of the headlights, etc. to the front seat) 3 REAR OF THE VEHICLE 6 DEALER SERVICE DEPARTMENT Eg. Location of the spare wheel, tool kit 7 WARRANTY AND MAINTENANCE CONDITIONS 7 4 REAR SEATS Eg. Warranty and maintenance documents (Service sheet or Eg. Child safety (lsofix fixing point) Modularity of the seats warranty & maintenance booklets), maintenance stamps 8 ISSUED WITH » Was your vehicle presented to you as stated above? Two set of keys YES NO Tool kit » Did your vehicle match your vehicle order? Spare tyre Vehicle invoice YES NO Insurance cover note Registration document Vehicle manual 233


key: chroma:document
string_value:
Delivery of your vehicle Comments: .................................................................................................................................................................................................................................................................. .................................................................................................................................................................................................................................................................. .................................................................................................................................................................................................................................................................. Please note that MG Motor India will not be responsible for any issues pertaining to Non Genuine Accessories fitted either by dealership or aftermarket. Should you require any further details regarding the vehicle handover or if you have any questions relating to your vehicle, please do not hesitate to contact your Sales or Delivery Advisor. ENJOY DRIVING YOUR NEW MG! CUSTOMER SIGNATURE DELIVERY ADVISOR SIGNATURE 1st EXEMPLARY: CUSTOMER 2nd EXEMPLARY: DELIVERY ADVISOR 234


key: chroma:document
string_value:
MG Motor New Vehicle Warranty MG Motor Vehicles in the MG MOTOR 2.2 Geographical coverage: range, delivered as new from 1st New Vehicle Warranty 2.2.1 This warranty covers any new April 2019 to the Customer by an vehicle sold within geographical Terms & Conditions authorized MG MOTOR DEALER, boundaries of INDIA. are warranted against any material, INDIA assembly or Manufacturing Defects If the vehicle is to be driven and, 1. Warning: by the Manufacturer. The New more importantly, registered outside Vehicle shall be covered under a the geographical area defined above, Your MG MOTOR vehicle is Warranty by MG MOTOR for a such vehicle will not be covered manufactured to meet the regulations period of under the current warranty as stated and environmental requirements herein. for Indian conditions. In case you • Personal Registration - 3 years relocate it to any other country than or Unlimited kilometers (whichever 2.3 The period of warranty on the INDIA, it may be very difficult to is earlier) vehicle shall not be deemed to be make modifications to comply with extended by repairs or replacements • Commercial Registration - the regulations and environmental of any parts. requirements of that country and 3 years or 1,00,000 kms (whichever 2.4 In the event the Original Purchaser it may be difficult to perform repair is earlier) of the vehicle transfers the vehicle service in that country. MG Motor new vehicle warranty during the period of warranty, it Please note that a MG MOTOR starts from the Delivery Date shown shall be obligation of the subsequent vehicle relocated to any other in the Owner’s Manual issued to purchaser to notify and inform MG country than India shall not be the Customer / First Owner of the Motor or its authorized dealer of covered by the warranty. vehicle upon delivery of the vehicle such transfer. purchased. (Transfer of ownership 2.5 If the vehicle identification number 2. The MG MOTOR New Vehicle of the vehicle does not alter the (VIN) of an insured vehicle is Warranty warranty period of a vehicle.) declared as total loss by the insurer, 2.1 Duration of MG MOTOR’S New any Warranty, Extended Warranty, Vehicle Warranty: free services, i-call, e-call and i-smart app (facilities if applicable) provided 235


key: chroma:document
string_value:
MG Motor New Vehicle Warranty in respect of such vehicle shall requested to contact your nearest 2.7 The MG MOTOR New Vehicle become null and void with effect MG MOTOR Dealer for more Warranty does not cover and from the date VIN of such vehicle is details. MG MOTOR India Private declared as total loss by the insurer. Limited (MG MOTOR) and 2.6.1 Battery: The warranty coverage / or MG MOTOR authorized for 12V / 48V Battery is valid for Field of Application: workshop shall not be 1 year starting from the Delivery 2.5 The Customer is covered for: Date shown in the Owner’s responsible for the following: 2.5.1 Free repair (parts, consumables and Manual issued to the Customer and 2.7.1 Normal maintenance services other labour) of any material or assembly shall be provided by the battery than free services*, including without defect duly found in the vehicle, at manufacturer as per their terms and limitation, cleaning and polishing, their own request, as well as any conditions. minor adjustments, engine tuning, oil repairs on damage caused by this 2.6.2 Tyre: The warranty coverage for top-up / fluid changes, Diesel Exhaust defect to other vehicle parts. Tyre is valid for 1 year starting Fluid (DEF) top-up / replacement, 2.5.2 24/7 assistance services as defined from the Delivery Date shown in filters replenishment, fastener re- in the “MG MOTOR Road Side the Owner’s Manual issued to the tightening, wheel balancing, wheel Assistance” section. Customer and shall be provided by alignment and tyre rotation etc. the respective tyre manufacturer 2.7.2 The indirect and remote It is the authorized MG MOTOR as per their warranty terms and consequences of any fault Dealer’s discretion to decide conditions. (loss of operation, duration of whether it is appropriate to repair or replace the defective part, whilst 2.6.3 Infotainment / Audio system: immobilization, etc.); keeping the Customer informed. The warranty coverage for 2.7.3 Vehicle components which have Infotainment / Audio system is undergone conversion work, and/or 2.6 Parts not covered under valid for 3 years from the Delivery specification and design changes and warranty conditions contained Date shown in the Owner’s Manual the consequences (deterioration, herein: issued to the Customer and shall premature wear and tear, alterations, be provided by the respective etc.) of the conversion work on The following are the parts not manufacturer as per their terms and other vehicle parts or components, covered by warranty conditions conditions. or on its specifications; contained herein. Hence, it is 236 *The right is reserved to change number of free services at any time without prior notice.


key: chroma:document
string_value:
MG Motor New Vehicle Warranty 2.7.4 The costs incurred by the Customer 2.7.6.5 Use of parts other than MG MOTOR pollution, plant-based deposits such for routine maintenance; Genuine Parts. as resin, animal-based deposits such as bird droppings, chemical deposits; 2.7.5 Replacement of parts due to normal 2.7.6.6 Any device and / or accessories not wear and tear resulting from use Supplied / Fitted by MG MOTOR. 2.7.7.4 Transportation of the vehicle; of the vehicle or from its mileage 2.7.6.7 Modifications, alterations, tampering 2.7.7.5 Using an adulterated / incorrect fuel; including but not limited to clutch, or improper repair. 2.7.7.6 Fitting accessories not approved by shocker absorbers, wiper blades, the manufacturer; brake drum, brake disk, brake pads, 2.7.6.8 Parts used in applications of which brake shoe, lamp, plugs, belts, linings, they were not designed or not 2.7.7.7 Fitting accessories approved by the bulbs, fuses, parts made of rubber, approved by MG MOTOR. manufacturer, but installed without observing the recommendations etc. 2.7.6.9 The vehicle in which the odometer defined by the manufacturer; 2.7.6 Damage or failure resulting due to has been tampered with, changed the following causes: aftermarket or been disconnected. 2.7.7.8 Damage due to airborne fallout, industrial fall out, acid rain, hail and 2.7.6.1 Poor vehicle maintenance, in 2.7.6.10 Slight irregularities not recognized wind storms, or other force majeure particular if the instructions for as affecting quality or function of the events like lightning, fire, floods, the treatment, the frequency of vehicle or parts, such as slight noise earthquakes, war, riots, attacks etc.; maintenance or care to be applied to or vibrations, or items considered the vehicle set out in the Owner’s characteristic of the vehicle. 2.7.7.9 Damage caused due to hydro-static lock, submerged vehicle. Manual have not been observed; 2.7.7 Damage caused by the following 2.7.7.10 Damage caused due to rodents; 2.7.6.2 Due to lack of use / operation of external causes: vehicle over prolonged period[s]; 2.7.7.11 Paint scratches, dents or similar 2.7.7.1 Accidents, impacts, scratches, paint or body damage. 2.7.6.3 Misuse, abuse, negligence, improper scoring, projection of gravel or solid driving habits, theft etc. of the bodies, hail, acts of vandalism; 2.7.7.12 Incidental or consequential damages, vehicle; including without limitation, loss of 2.7.7.2 Failure to observe the Manufacturer 2.7.6.4 Damage from stress, like use of recommendations; vehicles in races, rallies or as taxis. 2.7.7.3 Deposits due to atmospheric 237


key: chroma:document
string_value:
MG Motor New Vehicle Warranty time, inconvenience, loss of use of contact the nearest MG MOTOR 2.11 All operations, parts and labour, vehicle or commercial loss. authorized workshop member or carried out under the MG MOTOR MG MOTOR Assistance. New Vehicle Warranty are How does the MG MOTOR New 2.9 The MG MOTOR New Vehicle guaranteed until the new vehicle Vehicle Warranty work? Warranty does not apply, and warranty expires. 2.8 To be eligible for the MG MOTOR MG MOTOR and MG MOTOR 2.12 Transferring ownership of the New Vehicle Warranty, the authorized dealer members are vehicle shall not alter the application Customer must: exempt from all liabilities, if: conditions of the MG MOTOR New 2.8.1 check that the Owner’s Manual does 2.9.1 The vehicle has been driven under Vehicle Warranty. contain the Delivery Date of the conditions not in accordance with 3. The MG MOTOR Anti- vehicle - their warranty entitlement those stated in the Owner’s Manual corrosion Warranty: is dependent on this; (example but not limited to: vehicle 2.8.2 contact any workshop of the MG overloaded or taking part in any type 3.1 Duration of the Anti-Corrosion MOTOR Authorized Workshop of sports competition, etc.); Warranty: This warranty will apply Network – only such Workshop 2.9.2 The defect observed is due to the from the delivery date given on the have the authorization for operations Customer having had the vehicle Owner’s Manual for a period of: of this sort; repaired or serviced in a workshop • Personal Registration - 2.8.3 show the duly completed Owner’s outside the MG MOTOR authorized 3 years or Unlimited kilometers Manual, as proof of entitlement to the network and not observing MG (whichever is earlier) warranty and that the maintenance Motor’s recommendations on the • Commercial Registration - operations recommended by the subject. 3 years or 1,00,000 kms Manufacturer have been carried out; 2.10 By way of consideration for the parts (whichever is earlier). 2.8.4 have the defect covered by the MG supplied by MG MOTOR under 3.2 Geographical Coverage: The MOTOR New Vehicle Warranty the MG MOTOR New Vehicle geographical coverage of the Anti- confirmed as soon as possible, by a Warranty, parts replaced under this Corrosion Warranty is identical MG MOTOR authorized workshop warranty, shall legally become the to that for the MG MOTOR New in writing. If the vehicle is un- property of MG MOTOR. Vehicle Warranty. roadworthy, the Customer must 238


key: chroma:document
string_value:
MG Motor New Vehicle Warranty 3.3 Anti-Corrosion Warranty field 3.4 The MG MOTOR Anti- 3.5.2 The Customer shall show the of application Corrosion Warranty does not duly completed (delivery date and cover: validation of anti-corrosion test 3.3.1 In addition to the MG MOTOR New coupons) the Owner’s Manual as Vehicle Warranty, MG MOTOR 3.4.1 any damage which is not covered proof of their warranty entitlement. guarantees the bodywork and sub by the MG MOTOR New Vehicle frame of MG MOTOR vehicle Warranty, as defined at the start of 3.5.3 Application of the MG MOTOR Schedule I from perforation from the this booklet; Mechanical components Anti-Corrosion Warranty is subject interior, due to steel panel corrosion which are not an integral part of the to the anti-corrosion tests on the caused by a manufacturing, material bodywork or sub-frame (wheel rims, bodywork and sub-frame. Customer or protective product application exhaust system, etc.). shall ensure that these tests are defect. conducted at the mileage intervals 3.4.2 In case, repairs (including denting or stated in the Owner’s Manual, 3.3.2 This guarantee covers the repair painting) have been carried out on and at least once every two years. or replacement of components the body of the MG Motor Vehicle Scheduled maintenance services with perforated steel panel work in a workshop outside the MG in the MG MOTOR authorized due to a manufacturing, material MOTOR authorized network. workshop network incorporate or protective product application defect, acknowledged by the 3.5 Anti - Corrosion Warranty these tests. Manufacturer. conditions of application 3.5.4 If the Customer requests to have 3.3.3 It is authorized MG MOTOR 3.5.1 To obtain the Anti-Corrosion the anti-corrosion test conducted workshop’s discretion to decide Warranty, the Customer must independently of the scheduled whether it is appropriate to repair contact any Workshop of the MG maintenance service, the same will or replace these components, and to MOTOR Authorized Workshop be carried out at an extra cost to inform the Customer. Network - only such Workshop the Customer. have authorization for operations of 3.5.5 During these tests the Customer this sort. shall make sure that the professional carrying out the operation correctly completes the bodywork and sub frame test coupon, in order to 239


key: chroma:document
string_value:
MG Motor New Vehicle Warranty validate the continuation of the Anti- conditions of the Anti-Corrosion acknowledged by the Manufacturer, Corrosion Warranty. Warranty. with the MG MOTOR authorized workshop carrying out the 3.5.6 Repairs on any deterioration must The MG MOTOR Paintwork Warranty: operation, keeping the Customer be made as soon as possible. 3.6 Duration of the Paintwork informed. 3.5.7 The application of the MG MOTOR Warranty: MG MOTOR guarantees 3.8.2 This repair shall take into account Anti-Corrosion Warranty is also the bodywork paintwork and the general condition of the vehicle subject to bodywork and sub- painted parts paintwork (door with regard to its age, mileage and frame repairs being carried out mirrors, bumpers etc.) for 3 years or maintenance level. in accordance with MG MOTOR Unlimited kilometers (for Personal recommendations. Registration) 3 years or 1 lac kms 3.9 The MG MOTOR Paintwork 3.5.8 The repair or replacement of (for Commercial Registration) Warranty does not cover: components under the conditions (whichever is earlier) from the 3.9.1 any damage which is not covered described in the “field of application” Delivery Date of the new vehicle. by The MG MOTOR New Vehicle (Paragraph 7.3), shall taken into 3.7 Geographical Coverage: The Warranty, as defined at the start of account the general condition of geographical coverage of the this booklet; the vehicle with regard to its age, Paintwork Warranty is identical mileage and maintenance level. 3.9.2 damage due to force majeure events: to that for the MG MOTOR New lightning, fire, floods, earthquakes, 3.5.9 Parts replaced under the Anti- Vehicle Warranty. war, riots and attacks; Corrosion Warranty legally become 3.8 Paintwork Warranty field of the property of MG MOTOR. 3.9.3 Mechanical components which are application: not an integral part of the bodywork 3.5.10 Repairs and components fitted 3.8.1 This warranty covers the free repair or sub-frame (wheel rims, exhaust under the Anti-Corrosion Warranty or replacement of components system, etc.). are guaranteed until the end of the with inherent paintwork defects term of the original Anticorrosion Damage due to action of road (deterioration of lacquer or finishing Warranty. elements (sand, gravel, dust or varnish, due to any material, road debris) which results in stone 3.5.11 Transferring ownership of the manufacturing or application defect) chipping of paint or glass. vehicle does not alter the application 240


key: chroma:document
string_value:
MG Motor New Vehicle Warranty 3.9.4 In case, the denting or painting 3.10.5 Transferring ownership of the 5.2 Retention of maintenance service job has been carried out on the vehicle does not alter the application records. It may be necessary for the MG Motor Vehicle in a workshop conditions of the Paintwork customer to show that the required outside the MG MOTOR authorized Warranty. maintenance has been performed, as network. specified in this Owner’s Manual. 4. This warranty is the entire Warranty 5.3 In order to maintain the validity of 3.10 Paintwork Warranty conditions given by MG MOTOR and no this emission warranty, the vehicle of application Authorized Dealer of MG Motor must be serviced by Authorized or its or his agent or employee is 3.10.1 To obtain the Paintwork Warranty, MG Dealer in accordance with the authorized to extend or enlarge this the Customer must contact any Owner’s Manual. warranty and no Authorized Dealer workshop of the MG MOTOR of MG Motor or its or his agent or 5.4 Production of Pollution Under Authorized Workshop Network employee is authorized to make any Control (PUC) certificate valid for - only such Workshop have oral warranty on MG MOTOR’s the period immediately preceding authorization for operations of this behalf. the test during which the failure is sort. discovered, the test having been 3.10.2 The Customer shall show the duly 5. Owner’s Responsibility carried out either for obtaining a completed (delivery date) Owner’s 5.1 Proper use, maintenance and care new certificate, or pursuant upon Manual as proof of their entitlement of the vehicle in accordance with being directed by an officer as to the warranty. the instructions contained in the referred to in sub-rule (2) of Rule 3.10.3 By way of consideration for the parts Owner’s Manual. If the vehicle is 116 of the Central Motor Vehicle supplied by MG MOTOR under the subject to severe usage conditions, Rules. Paintwork Warranty, parts replaced like (but not limited to) operation 6 MG MOTOR reserves the right to under this warranty legally become in extremely dusty, rough, more make any change in design or make the property of MG MOTOR. repeated short distance driving or any improvement in the design, heavy city traffic during hot weather, 3.10.4 Repairs and components fitted structure, technology etc. of the maintenance of vehicle should be under the Paintwork Warranty are vehicle at any time without any done more frequently as mentioned guaranteed until the end of the term obligation to make the same change in this Owner’s Manual. of the original Paintwork Warranty. on the vehicles already sold. 241


key: chroma:document
string_value:
7. Warranty service shall be provided only by MG MOTOR’s Authorized Dealers and Dealer Service Branch. 8. MG MOTOR’s decision is final and binding on the Owner of the vehicle in all warranty matters. MG MOTOR reserves the right for the final decision on all warranty matters. The terms & conditions mentioned 9. The terms and conditions as contained herein shall be construed in accordance to the laws as applicable in India and all disputes arising out of this Warranty will be subject to the jurisdiction of Courts in Gurugram only. 242


key: chroma:document
string_value:
Roadside Assitance MG Roadside Assistance 24x7 Getting Help – What to do when you o Key problems: locked keys, lost keys, or need Assistance broken vehicle keys CALL 1800-100-6464 In the event of a breakdown or accident, o Tyre problems: puncture, bolts or valve simply call MG Roadside Assistance on 1800 related issues MG Roadside Assistance is designed to 100 6464 (toll-free from anywhere in India), enhance your overall MG ownership o Battery problems: flat battery or press the Call button on your car. When experience, by providing you with 24hrs/7days placing the call, please have the following o Fuel problems: out of fuel, incorrect fuel, emergency support related to the use of your information handy for assisting the operator or contaminated fuel (Twice a year, up to MG Motor Vehicle. Peace of mind motoring- in analysing the issue: 5 lit) guaranteed. • Description of the problem; o Road traffic accident where the vehicle is While it is our sincere hope that your travels immobilized are always trouble-free, breakdowns and road • Your location; traffic accidents do happen - our goal is to Assistance will be provided no matter where • Registered Contact phone number, ensure that even if your MG is immobilized, you are (i.e. at home, on the roadside, on the in case you are calling from a number whether at home or while travelling, any highway, in a parking lot, etc.), as long as you other than your registered number, as inconvenience to you and your family is are not already at an Authorized MG Dealer. registered with MG; minimized. • License plate number SUMMARY OF CUSTOMER BENEFITS Should you ever require assistance, all you need to do is dial our 24-hour assistance if you opt for your own vehicle assistance / Roadside Assistance at home or on the hotline: 1800 100 6464 and or press the recovery management, the cost for the same road Call button on your car and MG Roadside shall be borne by you. If your vehicle is immobilized, whether Assistance will be there to help. Vehicles will at home or on the road, MG Roadside be covered under this program for a period Covered Events Assistance will attend to your vehicle. For of 3 years from the Date of sale of the vehicle. • Mechanical or electrical breakdown conditions where we decide that the cause of leading to stoppage/immobility of the the breakdown/immobilizations can be solved vehicle at the roadside, a technician will be sent to try and mobilize your vehicle at your location. • Human error 243


key: chroma:document
string_value:
Roadside Assitance Vehicle Recovery Medical Coordination coverage (except islands, areas with If your vehicle is unable to be mobilized In case of a medical assistance required by limited entries). Vehicles will be covered following a mechanical or electrical you during the breakdown, MG Roadside under this program for a period of 3 breakdown, a recovery vehicle will be sent Assistance team will help for the medical years from the date of sale of the vehicle. to recover your vehicle to the nearest coordination. Assistance will be provided no matter authorized MG dealer. where you are (i.e. at home, on the Accommodation Assistance roadside, on the highways, in a parking Taxi In case of a breakdown occurring far lot, etc.), as long as you are not already at If your vehicle is recovered to an authorized from your hometown (not less than 100 an Authorized MG Dealer. MG Dealer, MG Roadside Assistance will also kilometres), and if so needed by you, MG provide taxi assistance. Roadside Assistance will help provide a hotel Non-covered Events accommodation for you for one night. MG Roadside Assistance is designed to Custody Services help only in “covered events” that lead to Program Overview – Definitions If towing is delayed, or if the technician stoppage / immobilization of your vehicle. As on spot is unable to fix your vehicle, MG • Covered Customers: a result, this program will not cover following Roadside Assistance will arrange for a The owner (or driver) and all the events, including but not limited to: personnel to take custody of your vehicle. passengers travelling in the vehicle at • Faulty fuel gauge the moment the roadside assistance Vehicle Recovery following an Accident was required, up to the legal passenger • Speedometer not working If your vehicle is unable to be mobilized limit of the vehicle. The customer may • Air-conditioning is not working following a road traffic accident, MG Roadside be asked to produce car/other identity • Passenger door(s) cannot be opened Assistance will organize to send a recovery documents to verify the eligibility under when there are no passengers in the vehicle to recover your vehicle from the this Program. vehicle accident site to the nearest authorized MG • Covered Vehicles and period of Dealer. • Boot cannot be opened cover: • Front and / or rear demisters are not All new MG vehicles sold by Authorised functioning MG Dealers in India are eligible for free MG Roadside Assistance with Pan India • Horn is not functioning 244


key: chroma:document
string_value:
Roadside Assitance • Damaged door mirrors • Other non-safety related lights/service • Breakdown is caused by deliberate • Rear view mirror is damaged, but it does warnings are illuminated damage, or participation or abetment in not obstruct the driver’s vision • Vehicle runs out of windscreen wiper a criminal act or offence; • Damaged or faulty fuel cap but vehicle has fluid • The immobilization is resulting from not run out of petrol and there is enough • Front or rear windscreen wipers faulty damage caused by intervention of the fuel in the tank to enable the vehicle to but weather conditions are fair police or other authorities; reach the nearest Authorized MG Dealer • Any damage resulting from the use of the • Sunroof cannot be opened General Exclusions vehicle against the recommendations of • Sunroof cannot be closed but weather The following scenarios are general exclusions the owner manual; conditions are fair, and the vehicle is not under the MG Roadside Assistance and • Any consequential costs and / or damage exposed to any security risk therefore MG Roadside Assistance will not to property as a result of a breakdown; be responsible for any assistance costs as a • Windows cannot be opened • Vehicles kept in a non-roadworthy result of any of the following: • Windows cannot be closed but weather condition or not serviced in conditions are fair, and the vehicle is not • Vehicle is involved in motor racing, accordance with the manufacturer’s exposed to any security risk. rallies, speed or duration tests, practice recommendations; runs, or operated outside, subject to the • Seat adjustor is faulty, but the vehicle can • The damage / immobilization is caused exclusivities provided herein and in the be safely driven due to any repair work done on the owner manual; • Passenger seat belts are faulty but there vehicle is from a workshop which is are no passengers in the vehicle • Assistance is required as a result of not a member of the MG Authorised wars, riots, uprising, mass political Workshop Network; • Faulty security system unless the vehicle demonstrations, pillage, strike, use for is immobilized or unless the alarm is • The damage / immobilization is caused military purposes or acts of terrorism, sounding continuously to the vehicle due to the negligence earthquake damage, freak weather • ABS lights are illuminated conditions, atmospheric phenomena, / intentional driving of the vehicle or tampering with the vehicle, even after • Air bag warning lights are illuminated nuclear transformation phenomena or becoming aware of the breakdown / fault radiation caused by artificial acceleration • Traction control lights are illuminated / damage. of atomic particles; 245


key: chroma:document
string_value:
Roadside Assitance • If the vehicle identification number General Terms and Conditions Locked Keys (VIN) of an insured vehicle is declared Remain with your Vehicle • Whilst we will always endeavour to as total loss by the Insurer, the Roadside provide assistance by the most efficient Assistance (RSA) provided in respect of • Once you have called MG Roadside method, modern security systems such vehicle shall become null and void Assistance, it is vital that you stay with sometimes make it extremely difficult with effect from the date VIN of such your vehicle. Should the MG Roadside for us to gain entry to your vehicle at vehicle is declared as total loss by the Assistance representative arrive at the roadside should the spare keys not insurer. your vehicle while it is unattended, the be available. If a forced emergency entry necessary work will not be carried out. is required, you will be asked to sign a declaration stating that you have granted Adverse Weather permission for this to take place and • On occasion, adverse weather conditions confirming that all costs relating to any such as floods, heavy rain, thunder / resulting damages to your vehicle will be lighting, other natural calamities or other your sole responsibility. external factors may affect our ability to provide services and it may become Replacement Costs physically impossible to assist you until • The replacement cost for any damaged the weather improves. During such part of the vehicle shall not be covered times, our main priority will be to ensure by MG Roadside Assistance, unless it is that you and your passengers are taken covered under any other warranty(ies) to a place of safety; the recovery of your provided by MG Motor, including the new vehicle may not be possible until weather vehicle warranty, as may be applicable conditions permit. and / or subscribed to by the owner of the MG vehicle. External Factors • MG will take every effort to reach you Right of Refusal once you make the call however external • MG Roadside Assistance shall have the conditions (including traffic, strike etc.), right to refuse any or all benefits under could delay such an effort. 246


key: chroma:document
string_value:
the program, if it is found that you had furnished false information relating to your eligibility or entitlements to the benefits provided under this program. Disputes • Courts situated within the jurisdiction of Gurugram alone shall have the exclusive jurisdiction to decide all disputes that may arise under this service. 247


key: chroma:document
string_value:
Service Coupon PDI (One day before delivery) VIN no. ......................................................................................... PDI no. .......................................................................................... Dear Customer, We are confident that you and your family would be enjoying the safe and Date of Delivery ......................................................................... comfortable drive of the MG Astor. Dealer Name............................................................................... We would like to undertake a thorough check-up of the vehicle at 1000 kms or 30 days, whichever occurs earlier. This will also allow us to reemphasize the Dealer Code ............................................................................... salient features of the Astor to you. Customer Name ........................................................................ In the unlikely event of an emergency assistance, please call your nearest MG Dealer or please feel free to call our 24 x 7 pulse hub at Contact No. ................................................................................ 1800 100 6464. Find your nearest MG authorized dealer by visiting www.mgmotor.co.in/tools/dealers --------------------------------------------------------------------------------------------------- I confirm that the vehicle has been inspected by me and delivered to my satisfaction. I do abide by MG terms & conditions laid forward for warranty and other vehicle maintenance details. Customer’s Signature Dealer Stamp & Signature Customer’s Signature Dealer Stamp & Signature


key: chroma:document
string_value:
Service Coupon 1st Free Inspection MG Motor Inspection 1 Month / 1000 km (whichever occurs earlier) - Petrol 1st Free Inspection 1 Month / 1000 km (whichever occurs earlier) - Petrol Engine Oil Check Fuel Lines for Leakages Brake Oil / Clutch Fluid Check HVAC for Satisfactory VIN ................................................................................................ Performance WS Washer Fluid Check Front Brake and Rear Regn. No. ..................................................................................... Check the DTC, Diagnose, Inspect Disk pad Clean-Inspect and Clear the all DTC Delivery Date .............................................................................. Date of Service ........................................................................... Kms ............................................................................................... I confirm that the job has been attended to my satisfaction. Customer’s Signature Dealer Stamp & Signature Customer’s Signature Dealer Stamp & Signature


key: chroma:document
string_value:
GENERAL STATUS REVIEW Check closing efforts of doors Central locking system Other functions UNDER HOOD Check fluid levels Engine oil level Brake oil level Coolant level Power steering oil Windshield washer level & add washer fluid UNDERBODY, WHEELS Visually check routing, leaks & damage Check tyre pressure ELECTRICAL CHECKS Malfunction indicator lamp Charging lamp Oil pressure lamp Parking brake lamp / indicator High beam / Turn signal Hazard indicator All other telltale lamp Cigarette lighter/rear defogger Check lighting system Horn / Radio / Outside Mirrors High / Low beam / Hazard signal Turn signal / Flash to pass signal Front/Rear fog lamps / Tail lamps Stop lamp / Reversing lamp / Trunk lamp DYNAMIC EVALUATION Steering function / noise / abnormal drag Clutch & gear shifting function / noise Accelerating & braking function / noise Check tyres Any other abnormal noise Note - For detailed information refer section ‘Maintenance Schedule’.


key: chroma:document
string_value:
Service Coupon 2nd Free Inspection MG Motor Inspection 6 Months / 5000 km (whichever occurs earlier) - Petrol 2nd Free Inspection 6 Months / 5000 km (whichever occurs earlier) - Petrol Check HVAC Engine Oil for Satisfactory Performance Air Filter Element VIN ................................................................................................ Check Front Brake and Rear Pollen / AC Filter Disk pad-Clean-Inspect Regn. No. ..................................................................................... Brake Oil / Clutch Fluid ATF (Trans Oil)* WS Washer Fluid Check Front and Rear Delivery Date .............................................................................. Check the DTC, Diagnose, Brake Disk Pad-Inspect* Inspect and Clear the all DTC Date of Service ........................................................................... Check Fuel Lines for Leakages Kms ............................................................................................... I confirm that the job has been attended to my satisfaction. Customer’s Signature Dealer Stamp & Signature Customer’s Signature Dealer Stamp & Signature


key: chroma:document
string_value:
Service Coupon 3rd Free Inspection MG Motor Inspection 1 Year / 10000 km (whichever occurs earlier) - Petrol 3rd Free Inspection 1 Year / 10000 km (whichever occurs earlier) - Petrol Steering Geometry / Wheel Balancing / Engine Oil Rotation / Tyre Pressure Oil Filter Check the DTC, Diagnose, Inspect VIN ................................................................................................ Washer Drain Plug and Clear the all DTC Regn. No. ..................................................................................... Air Filter Element Check Fuel Lines for Leakages Spark Plug Check HVAC for Delivery Date .............................................................................. Satisfactory Performance Pollen / AC Filter Check Front Brake and Rear Date of Service ........................................................................... Brake Oil / Clutch Fluid Disk pad-Clean-Inspect Acc Belt Fuel Filter* Kms ............................................................................................... Transmission Oil Drain Water from Fuel Filter* WS Washer Fluid I confirm that the job has been attended to my satisfaction. Customer’s Signature Dealer Stamp & Signature Customer’s Signature Dealer Stamp & Signature


key: chroma:document
string_value:
ENGINE CONTROL SYSTEM Drive Belt Engine Oil (Replace) (Alternator, Power Steering and A/C Compressor) Engine Oil Filter (Replace) Cooling System Hose and Connections Engine Coolant Fuel Filter Fuel Line and Connections Air Cleaner Element Spark Plugs & Spark Plug Wires CHASSIS AND BODY Exhaust Pipe & Mountings Brake Fluid Front Brake Discs & Pads Rear Brake Drums & Linings Parking Brake Brake Line and Connections (Including Booster) Manual Transaxle Fluid Steering Wheel & Linkage Wheel Alignment Wheel Balancing (When required or as suggested by (When required or as suggested by MG Motor retailer) MG Motor retailer) Power Steering Fluid and Line Drive Shaft Boots Safety Belts, Buckles & Anchorages Lubricate Locks, Hinges & Hood Latch Tyre Condition and Inflation Pressure & Rotation A/C Mesh Filter Chassis and Underbody Bolts and Nuts Tight / Secure Note - For detailed information refer section ‘Maintenance Schedule’.


key: chroma:document
string_value:
Change of Ownership Record Change of Ownership Record Model Registration or License Number VIN New Owner’s Name New Owner’s Address Telephone No. If resold by MG Motor Dealership Enter Dealer Stamp in Box above 257


key: chroma:document
string_value:
Periodic Maintenance Schedule - Astor (MT / CVT)^ 1 6 1 2 3 4 5 6 7 8 9 10 Years Month Months Year Years Years Years Years Years Years Years Years Years Operation / Processes for Replacement Frequency: Periodic Km / Year whichever is 1000* 5000* 10000* 20000 30000 40000 50000 60000 70000 80000 90000 100000 Service Schedule earlier Engine Oil 10K / 1Yr I I R R R R R R R R R R Oil Filter 10K / 1Yr R R R R R R R R R R Washer Drain Plug 10K/1 Year R R R R R R R R R R Pollen / AC Filter 20K / 2Yr I R I R I R I R I R Air Filter Element 30K / 3Yrs R R R Brake Oil / Clutch fluid 30K / 3Yrs I I I R I I R I I R I Fuel Filter 40K / 4Yrs R R Spark Plug 40K I I I I R I I I R I I Acc Belt Inspection I I I I I I I I I I I I Coolant Change 80K / 8Yrs I I I I I I I R I I Transmission Oil 100K / 10Yrs I WS Washer Fluid 10K/1 Year I I I I I I I I I I I I Steering Geometry / Wheel 10K/1 Year I I I I I I I I I I Balancing / Rotation Check the DTC, Diagnos, 10K/1 Year I I I I I I I I I I I I Inspect and clear the all DTC Check Fuel lines for Leakages Every Service I I I I I I I I I I I I Check HVAC for Every Service I I I I I I I I I I I I Satisfactory Performance Check front Brake and Rear Every Service I I I I I I I I I I I I Disk pad-Clean-Inspect Vehicle Software Update* Every service U U U U U U U U U U U U Sunroof Operation Special maintenance item Clean the guide rails and apply special grease when necessary, check for water drain function of sunroof, and clean as required. Symbol Abbreviation: R - Replace • U - Check for Vehicle Software version and Update (including campaigns) if required • I - Inspect (Top up if required/Adjust/Gap setting/Clean) • NA: Not applicable • * Labour Free Services. - Tightening of underbody fasteners, door adjustments and functional checks of all the systems during every service is mandatory. - Check the coolant level and top up as required, replace if it is contaminated/ discoloured or there is sludge formation. - Filters, Fluid, Grease, Consumables, Components, Wheel Alignment, Wheel Balancing etc. (but not limited to mentioned) will be replaced on chargeable basis. ^ Periodic Maintenance Schedule is for reference. MG reserves right to change the Periodic Maintenance Schedule. For latest Schedule, please refer MYMG APP / Website Owner’s Manual.


key: chroma:document
string_value:
Periodic Maintenance Schedule - Astor (AT)^ 1 6 1 2 3 4 5 6 7 8 9 10 Years Month Months Year Year Year Year Year Year Year Year Year Year Operation / Processes for Replacement Frequency: Periodic Km / Year whichever is 1000* 5000* 10000* 20000 30000 40000 50000 60000 70000 80000 90000 100000 Service Schedule earlier Engine Oil 10K / 1Yr I I R R R R R R R R R R Oil Filter 10K / 1Yr R R R R R R R R R R Washer Drain Plug 10K/1 Year R R R R R R R R R R Pollen / AC Filter 20K / 2Yr I R I R I R I R I R Air Filter Element 30K / 3Yrs R R R Brake Oil / Clutch fluid 30K / 3Yrs I I I R I I R I I R I Spark Plug 40K I I I I R I I I R I I Acc Belt Inspection I I I I I I I I I I I I Coolant Change 80K / 8Yrs I I I I I I I R I I Transmission Oil 100K / 10Yrs I WS Washer Fluid 10K/1 Year I I I I I I I I I I I I Steering Geometry / Wheel 10K/1 Year I I I I I I I I I I Balancing / Rotation Check the DTC, Diagnos, 10K/1 Year I I I I I I I I I I I I Inspect and clear the all DTC Check Fuel lines for Leakages Every Service I I I I I I I I I I I I Check HVAC for Every Service I I I I I I I I I I I I Satisfactory Performance Check front Brake and Rear Every Service I I I I I I I I I I I I Disk pad-Clean-Inspect Vehicle Software Update* Every service U U U U U U U U U U U U Sunroof Operation Special maintenance item Clean the guide rails and apply special grease when necessary, check for water drain function of sunroof, and clean as required. Symbol Abbreviation: R - Replace • U - Check for Vehicle Software version and Update (including campaigns) if required • I - Inspect (Top up if required/Adjust/Gap setting/Clean) • NA: Not applicable • * Labour Free Services. - Tightening of underbody fasteners, door adjustments and functional checks of all the systems during every service is mandatory. - Check the coolant level and top up as required, replace if it is contaminated/ discoloured or there is sludge formation. - Filters, Fluid, Grease, Consumables, Components, Wheel Alignment, Wheel Balancing etc. (but not limited to mentioned) will be replaced on chargeable basis. ^ Periodic Maintenance Schedule is for reference. MG reserves right to change the Periodic Maintenance Schedule. For latest Schedule, please refer MYMG APP / Website Owner’s Manual.


key: chroma:document
string_value:
Maintenance Record Sheet MAINTENANCE RECORD SHEET (Repair Category - Free Service / Paid Service / Running Repair / Accident Repair) Repair Repair Name of Servicing Service Adv. R.O. No. Kms. Details of Repair Done Retailer Stamp Date Category Retailer Sign. 260


key: chroma:document
string_value:
Maintenance Record Sheet MAINTENANCE RECORD SHEET (Repair Category - Free Service / Paid Service / Running Repair / Accident Repair) Repair Repair Name of Servicing Service Adv. R.O. No. Kms. Details of Repair Done Retailer Stamp Date Category Retailer Sign. 261


key: chroma:document
string_value:
VEHICLE RECORD SHEET MODEL CHASSIS NO. ENGINE NO. KEY NO. DATE OF DELIVERY MILEAGE (KM) BATTERY MAKE SR NO./ BATCH CODE TYRE TYRE LOCATION FR RH FR LH RR RH RR LH MAKE BATCH NUMBER OWNER'S NAME & ADDRESS: ADDRESS OF SELLING DEALER Showroom: Workshop: For any feedback, please call Toll free No. 1800 100 6464


key: chroma:document
string_value:
www.mgmotor.co.in 1800 100 6464 MG Motor India Pvt. Ltd. All information, illustrations and specifications contained in this Owner's Manual are based on the latest production information available at the time of publication. The right is reserved to make changes at any time without notice. Version: 01-10/2021/5000 (2021) 1 0 9 0 8 1 8 6


